Здравствуйте! Не запускается плата GD2. Выдает ошибку FLASH и уходит в постоянную перезагрузку. Как можно устранить неисправность? Текст загрузки прилагается.
*** BIOS Version 3EH30227GQAA bios100/010.014 ***
*** Generated on Mar/5/2008 at 14:05 ***
memory test started lng=133169152 with 0
running flash(soldered=1 socket=0)=1,BIOScase:4,BIOSv24:0,verrou=1,algoNOR=1,size=1,base=3FF80000
DIMM characteristics->: JEDEC Manu ID:É,......
Memory type(EDO,FPM..):0x 4
# of row address:13
# of col address 9
# of module row 1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI:scan_bus for bus 0
PCI:bus=00h,devfn=00h ,[vendor:device]=[1022h/3000h]
PCI:bus=00h,devfn=60h ,[vendor:device]=[100Bh/0020h]
PCI:bus=00h,devfn=98h ,[vendor:device]=[1064h/2101h]
PCI:scan_buses with 00h secondary buses
PCI:command = 3FFH for device 00:00
PCI: Assigning I/O space FC00-FCFF for 00:60 BAR= 10
PCI:Assign memory space BFFFF000H to BFFFFFFFH for device 00:60
PCI:command = 3FFH for device 00:60
PCI:Assign memory space BFFFD000H to BFFFDFFFH for device 00:98
PCI: Assigning I/O space FD00-FD1F for 00:98 BAR= 14
PCI: Unable to handle I/O allocation for 00:98 (FF04) BAR= 18
PCI:command = 3FFH for device 00:98
assigning irq10 to xchange
B0 = 17
DRCTMCTL = 1E
DRCCTL = 8
DBCTL = 11
Set external RTC
Set Internal RTC
No external RTC detected
gpbus sig timing : 0-2-1-2-1-2!
CMOS is available
Xchange PCI mem base OK: 0,mbx= BFFFD000
dsp_accesses.stat_ctrl= FD00
Xchange PCI IO base OK: 0
Xchange irq OK: A
PCI command read for natsemi : 347
PCI Master Bit Setting...
pci_command set to: 357
0 80 9F 81 6F 84 ,IRQ 12.on interrupt pin:2
eth0: Transceiver status 0x 7849 advertising 5E1
Flashfx version:700.014.700c
Flash 2Gbit Support activated !!
GC-forced on Soft Error activated !!
NAND Flash Comfiguration:
CPU size : 128 MBytes
free spare blocks: 4
NAND Flash Details:
chip #0 : Type=NAND01GW3B Id=20F1H Size=128(MBytes) Unit size=131072 Page Size=2048
time :sec=46,min=12,hour= 2,DoW= 7,date= 1,Month= 1,year= 0
time :sec=50,min=12,hour= 2,DoW= 7,date= 1,Month= 1,year= 0
ALIZE informations :
Memory Detected : 131072 Ko
Flash Detected
DaughterBoard Detected
DSP Voip Found : 1
XCHANGE Detected
XCHANGE Chip Initialization OK
Ethernet Found : 1
Ethernet Chip Initialization OK
Hard Disk Not Detected
PCM11 selected
CPU at 133 mhz
check lock RTC
value of DIL switch 2
YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW !
BATMODE testing
Static Boot from hard disk #0(3)
unable to boot on DISK
Static Boot from No Boot Device selected(0)
Static Boot from flash NAND mother(1)
FLASHFX error: VBF ECC on device 0
[Flash NAND] Read Spare with VBFECC check Failed -> Process Bad Block for page 0x07B8E800
Failed read Redundant area at @=0x2EC00
BOOT Sector Found on NAND Flash Drive #0
Shutdown of the interface 0 = 0
init ethernet interface 1 not done
Watch dog started
FLASHFX error: VBF ECC on device 0
[Flash NAND] Read Spare with VBFECC check Failed -> Process Bad Block for page 0x07B8E800
Failed read Redundant area at @=0x2EC00
GRUB stopping after 101 reading, last virt sector= 2EH, phys sector= 21224H, return code= 10010HðÇyAlize BIOS Monitor
*** BIOS Version 3EH30227GQAA bios100/010.014 ***
*** Generated on Mar/5/2008 at 14:05 ***