Уважаемые дамы и господа! Для вас сохранен старый форум по адресу http://forum.intersyst.ru
Здравствуйте! Не запускается плата GD2. Выдает ошибку FLASH и уходит в постоянную перезагрузку. Как можно устранить неисправность? Текст загрузки прилагается. *** BIOS Version 3EH30227GQAA bios100/010.014 *** *** Generated on Mar/5/2008 at 14:05 *** memory test started lng=133169152 with 0 running flash(soldered=1 socket=0)=1,BIOScase:4,BIOSv24:0,verrou=1,algoNOR=1,size=1,base=3FF80000 DIMM characteristics->: JEDEC Manu ID:É,...... Memory type(EDO,FPM..):0x 4 # of row address:13 # of col address 9 # of module row 1 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI:scan_bus for bus 0 PCI:bus=00h,devfn=00h ,[vendor:device]=[1022h/3000h] PCI:bus=00h,devfn=60h ,[vendor:device]=[100Bh/0020h] PCI:bus=00h,devfn=98h ,[vendor:device]=[1064h/2101h] PCI:scan_buses with 00h secondary buses PCI:command = 3FFH for device 00:00 PCI: Assigning I/O space FC00-FCFF for 00:60 BAR= 10 PCI:Assign memory space BFFFF000H to BFFFFFFFH for device 00:60 PCI:command = 3FFH for device 00:60 PCI:Assign memory space BFFFD000H to BFFFDFFFH for device 00:98 PCI: Assigning I/O space FD00-FD1F for 00:98 BAR= 14 PCI: Unable to handle I/O allocation for 00:98 (FF04) BAR= 18 PCI:command = 3FFH for device 00:98 assigning irq10 to xchange B0 = 17 DRCTMCTL = 1E DRCCTL = 8 DBCTL = 11 Set external RTC Set Internal RTC No external RTC detected gpbus sig timing : 0-2-1-2-1-2! CMOS is available Xchange PCI mem base OK: 0,mbx= BFFFD000 dsp_accesses.stat_ctrl= FD00 Xchange PCI IO base OK: 0 Xchange irq OK: A PCI command read for natsemi : 347 PCI Master Bit Setting... pci_command set to: 357 0 80 9F 81 6F 84 ,IRQ 12.on interrupt pin:2 eth0: Transceiver status 0x 7849 advertising 5E1 Flashfx version:700.014.700c Flash 2Gbit Support activated !! GC-forced on Soft Error activated !! NAND Flash Comfiguration: CPU size : 128 MBytes free spare blocks: 4 NAND Flash Details: chip #0 : Type=NAND01GW3B Id=20F1H Size=128(MBytes) Unit size=131072 Page Size=2048 time :sec=46,min=12,hour= 2,DoW= 7,date= 1,Month= 1,year= 0 time :sec=50,min=12,hour= 2,DoW= 7,date= 1,Month= 1,year= 0 ALIZE informations : Memory Detected : 131072 Ko Flash Detected DaughterBoard Detected DSP Voip Found : 1 XCHANGE Detected XCHANGE Chip Initialization OK Ethernet Found : 1 Ethernet Chip Initialization OK Hard Disk Not Detected PCM11 selected CPU at 133 mhz check lock RTC value of DIL switch 2 YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW ! BATMODE testing Static Boot from hard disk #0(3) unable to boot on DISK Static Boot from No Boot Device selected(0) Static Boot from flash NAND mother(1) FLASHFX error: VBF ECC on device 0 [Flash NAND] Read Spare with VBFECC check Failed -> Process Bad Block for page 0x07B8E800 Failed read Redundant area at @=0x2EC00 BOOT Sector Found on NAND Flash Drive #0 Shutdown of the interface 0 = 0 init ethernet interface 1 not done Watch dog started FLASHFX error: VBF ECC on device 0 [Flash NAND] Read Spare with VBFECC check Failed -> Process Bad Block for page 0x07B8E800 Failed read Redundant area at @=0x2EC00 GRUB stopping after 101 reading, last virt sector= 2EH, phys sector= 21224H, return code= 10010HðÇyAlize BIOS Monitor *** BIOS Version 3EH30227GQAA bios100/010.014 *** *** Generated on Mar/5/2008 at 14:05 ***
Или использовать б\у процессор от ОХО - в режим GD он переводится джамперами. На форуме есть эта информация.
15.08.2019 10:05:21, TMC.]]>
самое простое - заменить на другую плату GD2, если есть в наличии.
Можно попробовать перепрошить Flash с помощью PC Installer'a, но это редко помогает. У вас во флэш не осталось свободных запасных блоков. 4 блока зарезервированы для производителя - free spare blocks: 4.
15.08.2019 09:28:45, etc.]]>
15.08.2019 08:48:34, teleshel.]]>