I+#:
IP mode - dinamyc
IP? S\net, route, tftp1, tftp2, tftpb - 255.255.255.255
T-port - 69
CPU1 - 010.250.001.003
CPU1 - 255.255.255.255
USE VLAN+
id - 250
strict VLAN+
DHCP user class-
Class - iptouch.class0

если я не меняя IP параметры платы INTIP и CPU, сведу в один switch Плату, процессор и телефон, этого будет достаточно, чтобы телефон заработал, держа в уме, что проблема в локальной сети предприятия?!

┌─Review/Modify: TSC IP User───────────────────────────────────────────
│
│             Node Number (reserved) : 1
│                   Directory Number : 5006
│                   Directory Number : 5006
│
│                           Set Type + IPTouch 4028
│             Voice Coding Algorithm + Default
│          Terminal Ethernet Address : 00:80:9f:8d:d8:84
│                         IP Address : Unused
│                   IP Domain Number : 0
│            Use of volume in system + YES
│        Reset For Update Authorized + YES
│             IP-Softphone Emulation + NO
│
в IP параметрах телефона прописан только МАС адрес, который я вбивал в ручную.
IP address прописать не могу, поле не активно
Не поднимаются, т.е. доходят до этапа 2 из 5 и затем через некоторое время сами перегружаются.
Были некоторые проблемы с локальной сетью, пришлось вставать на порты коммутаторов и искать рабочие порты, таким образом удалось реанимировать платы. Платы в сервисе теперь, аналогично поступил и с телефонами, нашел рабочий порт и встал на него. Каким образом я могу исключить вариант того что проблема не в станции(телефонах), а именно в сети?!

При перезагрузке АТС станция сама включила Secured. На данный момент не Secured. удалось поднять все платы INTIPA. у всех статус In service.пингую каждую по IP с компьютера через который захожу на CPU.
НО: телефоны IP touch все равно не поднимаются.

было сделано следующее: Вставал на порт коммутаторов расположенных в здании, куда подключены платы INITIPA и CPU, выяснил, что те ip которые раздавали коммутаторы на порты в которые были включены платы вообще из другой подсети, тогда решился сменить ip адреса на всех платах и CPU. Начал смотреть при помощи команды config происходит ли что то, или же нет. Три платы сменили статус с "reg not unit" на "init 1 run" и зависли с этим статусом.Тогда решил сделать reboot АТС, и вновь все вернулось на круги своя как говорится(((
Честно говоря уже не знаю что и думать. Такое ощущение что по MAC адресам платы достукиваются до CPU, так как на нем куча инцидентов с их IP адресами. а дальше темный лес....

проверил MAC адреса, они совпадают. Т.е. в менеджменте и визуально на плате.

не вышло, говорит что адрес уже занят CPU
пробовал использовать хаб, чтобы исключить неисправность сети, проблема не решилась((

What is your choice ? 2

Warning: your system is secured, so no default route will be created with this d
efault router !

Default router name ? 10.0.0.1

The Internet name you gave hasn't a correct format. You must give a string conta
ining only letters, digits and (.-_) and beginning with a letter. The maximal le
ngth is 64.

Default router name ? route

The name you gave isn't in our hosts database. Do you want to add it and so
give the corresponding address (y/n default is 'n') ? y

Default router address ? 10.0.0.1

The address you gave 10.0.0.1 is already used for CPUIPADDR.

1. все 4 платы INITIPA
2. если все так как вы говорите в графе шлюз должно быть пусто?
3. необходимо сравнить визуально

Существующая схема следующая:платы INITIPA имеют IP адреса из диапазона 10.250.1.50-10.250.1.100, Шлюз указан 10.250.1.1, данный адрес прописан в Ethernet parametrs для 19 корзины(мифической), а шлюзом мифической корзины является 10.250.1.254. вот, на первый взгляд вроде все ок, один вопрос, почему нельзя сразу направить платы на шлюз 10.250.1.254, зачем нужена мифическая корзина №19?
Если CPU ругается на MAC адреса плат INITIPA, то что можно с ними сделать??они все разные, прописываются сами, максимум я могу их проверить визуально и сравнить с теми, которые прописались за плата в менеджменте.

The internet accesses to the PABX are currently NOT SECURED.

WARNING : Only machines declared as trusted hosts
         will be able to have access to the PABX.

Do you want to secure your Internet accesses (y/n default is n)

Система не защищена, при добавлении trusted hosts пишет следующее:

There is no range of trusted hosts declared on your system !


WARNING : the following trusted hosts are DHCP addresses declared by MAO,
they cannot be modified by netadmin.

Range of trusted hosts

Думаю дело не в безопасности.
""Можно подробнее. Как я понимаю, адрес IP должен быть в диапазоне от 10.250.1.50-10.250.1.100, данное условие сохраняется. Адреса 4-х INITIPA плат 50-53 в конце. Теперь хотелось бы понять что в моем случае должно являться шлюзом. Если я правильно понимаю, то это IP адрес коммутатора, через который осуществляется соединение или же это IP адрес процессора??на данный момент прописан адрес 10.250.1.1, телнетом я могу зайти по этому адресу на АТС, наверно некорректно указывать этот адрес в графе Шлюз платы INITIP? если я правильно понимаю адрес шлюза должен быть 10.250.1.254:
11.2.Restricted access
======================


 1. 'View trusted hosts'

 2. 'View associated services'

 3. 'Add/Update a trusted host'

 4. 'Add/Update a range of trusted hosts'

 5. 'Update type of a trusted host'

 6. 'Remove trusted hosts'

 0. 'Previous menu'

What is your choice ? 1

IP name        | IP address      | Gateway IP Name | Type of host
============================================================­======
router         | 10.250.1.254    | localhost       | Router

Требуется ли рестар CPU после изменения шлюза плат INITIPA?

а можно подробнее где именно в netadmin -m, security можно посмотреть?
зашел под рутом, один лог заинтересовал. В нем упоминался IP адрес одной из плат INITIPA:
11.2.Restricted access
======================


 1. 'View trusted hosts'

 2. 'View associated services'

 3. 'Add/Update a trusted host'

 4. 'Add/Update a range of trusted hosts'

 5. 'Update type of a trusted host'

 6. 'Remove trusted hosts'

 0. 'Previous menu'

What is your choice ? 1

IP name        | IP address      | Gateway IP Name | Type of host
============================================================­======
router         | 10.250.1.254    | localhost       | Router



<return> to continue. 2

There is no range of trusted hosts declared on your system !


WARNING : the following trusted hosts are DHCP addresses declared by MAO,
they cannot be modified by netadmin.

Range of trusted hosts

First IP address | Last IP address  | Gateway IP Name | Type of host
============================================================­================
=============
10.250.1.50      | 10.250.1.100     | localhost       | IP-equipment

поключился при помощи ком порта к станции и пошли следующие инциденты, в том числе и про initip(привел только часть лога, т.к. он повторяется):

(1)xa000000> 13/02/14 18:43:40 000001M|002/02/-/---|=3:0747=Config error or Loss
of IP connection: 4,(2,2),10.250.1.51,00:80:9f:8b:d9:58
13/02/14 18:44:08 000001M|000/17/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(0,17),10.250.1.50,00:80:9f:8b:d4:46
13/02/14 18:44:13 000001M|002/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:44:23 000001M|003/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(3,2),10.250.1.52,00:80:9f:8b:d9:59
13/02/14 18:44:25 000001M|004/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(4,2),10.250.1.53,00:80:9f:81:f9:c8
13/02/14 18:44:41 000001M|000/17/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:44:56 000001M|003/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:44:58 000001M|004/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:45:18 000001M|---/--/-/---|=2:0275=ACCOUNTING: Appli PRINTING : feat
ure incident 10 2
13/02/14 18:46:14 000001M|002/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(2,2),10.250.1.51,00:80:9f:8b:d9:58
13/02/14 18:46:45 000001M|000/17/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(0,17),10.250.1.50,00:80:9f:8b:d4:46
13/02/14 18:46:47 000001M|002/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:46:57 000001M|004/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(4,2),10.250.1.53,00:80:9f:81:f9:c8
13/02/14 18:47:10 000001M|003/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(3,2),10.250.1.52,00:80:9f:8b:d9:59
13/02/14 18:47:18 000001M|000/17/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:47:30 000001M|004/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:47:44 000001M|003/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
timed out waiti

Alcatel-Lucent OmniPCX Enterprise

xa000000 login: 13/02/14 18:49:10 000001M|002/02/-/---|=3:0747=Config error or L
oss of IP connection: 4,(2,2),10.250.1.51,00:80:9f:8b:d9:58
13/02/14 18:49:22 000001M|000/17/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(0,17),10.250.1.50,00:80:9f:8b:d4:46
13/02/14 18:49:44 000001M|002/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:49:54 000001M|004/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(4,2),10.250.1.53,00:80:9f:81:f9:c8
13/02/14 18:49:55 000001M|000/17/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:49:58 000001M|003/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(3,2),10.250.1.52,00:80:9f:8b:d9:59
13/02/14 18:50:28 000001M|004/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:50:31 000001M|003/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:51:56 000001M|002/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(2,2),10.250.1.51,00:80:9f:8b:d9:58
13/02/14 18:52:10 000001M|000/17/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(0,17),10.250.1.50,00:80:9f:8b:d4:46
13/02/14 18:52:29 000001M|002/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:52:37 000001M|004/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(4,2),10.250.1.53,00:80:9f:81:f9:c8
13/02/14 18:52:43 000001M|000/17/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:52:45 000001M|003/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(3,2),10.250.1.52,00:80:9f:8b:d9:59
13/02/14 18:53:10 000001M|004/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:53:18 000001M|003/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:54:52 000001M|000/17/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(0,17),10.250.1.50,00:80:9f:8b:d4:46
13/02/14 18:54:54 000001M|002/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(2,2),10.250.1.51,00:80:9f:8b:d9:58
13/02/14 18:55:25 000001M|000/17/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:55:27 000001M|002/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:55:33 000001M|004/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(4,2),10.250.1.53,00:80:9f:81:f9:c8
13/02/14 18:55:35 000001M|003/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(3,2),10.250.1.52,00:80:9f:8b:d9:59
13/02/14 18:56:06 000001M|004/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:56:08 000001M|003/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:57:30 000001M|000/17/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(0,17),10.250.1.50,00:80:9f:8b:d4:46
13/02/14 18:57:32 000001M|002/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(2,2),10.250.1.51,00:80:9f:8b:d9:58
13/02/14 18:58:03 000001M|000/17/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:58:05 000001M|002/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:58:11 000001M|004/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(4,2),10.250.1.53,00:80:9f:81:f9:c8
13/02/14 18:58:34 000001M|003/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(3,2),10.250.1.52,00:80:9f:8b:d9:59
13/02/14 18:58:44 000001M|004/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 18:59:08 000001M|003/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:00:25 000001M|002/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(2,2),10.250.1.51,00:80:9f:8b:d9:58
13/02/14 19:00:30 000001M|000/17/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(0,17),10.250.1.50,00:80:9f:8b:d4:46
13/02/14 19:00:51 000001M|004/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(4,2),10.250.1.53,00:80:9f:81:f9:c8
13/02/14 19:00:59 000001M|002/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:01:03 000001M|000/17/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:01:07 000001M|003/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(3,2),10.250.1.52,00:80:9f:8b:d9:59
13/02/14 19:01:24 000001M|004/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:01:40 000001M|003/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:02:59 000001M|002/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(2,2),10.250.1.51,00:80:9f:8b:d9:58
13/02/14 19:03:11 000001M|000/17/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(0,17),10.250.1.50,00:80:9f:8b:d4:46
13/02/14 19:03:32 000001M|002/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:03:39 000001M|004/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(4,2),10.250.1.53,00:80:9f:81:f9:c8
13/02/14 19:03:44 000001M|000/17/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:03:47 000001M|---/--/-/---|=2:0275=ACCOUNTING: Appli PRINTING : feat
ure incident 2 0
13/02/14 19:03:47 000001M|---/--/-/---|=2:0276=External accounting application 4
760 : NO RECOVERY
13/02/14 19:03:48 000001M|003/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(3,2),10.250.1.52,00:80:9f:8b:d9:59
13/02/14 19:04:13 000001M|004/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:04:21 000001M|003/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:05:47 000001M|002/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(2,2),10.250.1.51,00:80:9f:8b:d9:58
13/02/14 19:06:11 000001M|000/17/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(0,17),10.250.1.50,00:80:9f:8b:d4:46
13/02/14 19:06:20 000001M|002/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:06:27 000001M|003/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(3,2),10.250.1.52,00:80:9f:8b:d9:59
13/02/14 19:06:33 000001M|004/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(4,2),10.250.1.53,00:80:9f:81:f9:c8
13/02/14 19:06:44 000001M|000/17/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:07:00 000001M|003/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:07:06 000001M|004/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:08:36 000001M|002/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(2,2),10.250.1.51,00:80:9f:8b:d9:58
13/02/14 19:08:49 000001M|000/17/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(0,17),10.250.1.50,00:80:9f:8b:d4:46
13/02/14 19:09:10 000001M|002/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:09:13 000001M|003/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(3,2),10.250.1.52,00:80:9f:8b:d9:59
13/02/14 19:09:22 000001M|000/17/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:09:31 000001M|004/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(4,2),10.250.1.53,00:80:9f:81:f9:c8
13/02/14 19:09:47 000001M|003/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:10:04 000001M|004/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:11:21 000001M|002/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(2,2),10.250.1.51,00:80:9f:8b:d9:58
13/02/14 19:11:48 000001M|000/17/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(0,17),10.250.1.50,00:80:9f:8b:d4:46
13/02/14 19:11:54 000001M|002/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:12:03 000001M|003/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(3,2),10.250.1.52,00:80:9f:8b:d9:59
13/02/14 19:12:06 000001M|004/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(4,2),10.250.1.53,00:80:9f:81:f9:c8
13/02/14 19:12:21 000001M|000/17/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:12:36 000001M|003/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:12:39 000001M|004/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:14:09 000001M|002/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(2,2),10.250.1.51,00:80:9f:8b:d9:58
13/02/14 19:14:33 000001M|000/17/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(0,17),10.250.1.50,00:80:9f:8b:d4:46
13/02/14 19:14:38 000001M|003/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(3,2),10.250.1.52,00:80:9f:8b:d9:59
13/02/14 19:14:42 000001M|002/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:15:05 000001M|004/02/-/---|=3:0747=Config error or Loss of IP connec
tion: 4,(4,2),10.250.1.53,00:80:9f:81:f9:c8
13/02/14 19:15:06 000001M|000/17/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:15:11 000001M|003/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
13/02/14 19:15:38 000001M|004/02/-/---|=2:4409=INT-IP Error during startup seque
nce code 7 (status 0xafa11 0x0000)
(873349:018525) Noe set: Error set property!
(873349:018526) Dump: .01.1a.31.00.00.06.02.0c.02.00.a1
(873349:018527) Dump of error message
(873349:018528) Dump: .15.04.0d.00.0a.02.85.12.60.ff.00.00.00.00.00.00.00.5b.31.
30
(873349:018529) Dump: .38.20.6e.6f.65.70.5f.64.65.63
13/02/14 19:15:51 000001M|---/--/-/---|=0:1612=Protocol error on Alcatel 8&9 ser
ies, type 13 (neqt 1029)
13/02/14 19:15:51 000001M|---/--/-/---|=3:1613=15.04.0d.00.02.02.85.12.60.ff.00.
00.00.00.00
13/02/14 19:16:14 000001M|000/22/0/000|=3:1307=MCDU in distri tab entity 1, col
Night , line 4 incorrect or missing
13/02/14 19:16:14 000001M|000/22/0/000|=3:1307=MCDU in distri tab entity 1, col
Night , line 4 incorrect or missing
13/02/14 19:16:14 000001M|000/22/0/000|=3:1307=MCDU in distri tab entity 0, col
Night , line 4 incorrect or missing
13/02/14 19:16:44 000001M|000/22/0/000|=3:1307=MCDU in distri tab entity 0, col
Night , line 4 incorrect or missing
(873996:018530) Noe set: Error set property!
(873996:018531) Dump: .01.1a.31.00.00.06.02.0c.02.00.a1
(873996:018532) Dump of error message
(873996:018533) Dump: .15.04.0d.00.0a.02.85.12.60.ff.00.00.00.00.00.00.00.5b.31.
30
(873996:018534) Dump: .38.20.6e.6f.65.70.5f.64.65.63
13/02/14 19:16:55 000001M|---/--/-/---|=0:1612=Protocol error on Alcatel 8&9 ser
ies, type 13 (neqt 1029)
13/02/14 19:16:55 000001M|---/--/-/---|=3:1613=15.04.0d.00.02.02.85.12.60.ff.00

добрый день vad.
на процессор захожу по адресу 10.250.1.3
в netadmin точно не знаю пользовались безопасностью или нет, т.к. станцию принял в том состоянии в котором она сейчас.
Адрес шлюза имел ввиду при создании платы initipa, там указан адрес 10.250.1.1.
данный адрес прописан на "мифической плате" в 19 корзине.
подскажите какой последовательностью действий можно выявить причину неполадки, возможны ли какие либо ошибки в БД?

удалось найти и подключиться к плате initip, ниже лог:
Из лога я понял лишь то, что плата не может найти процессор и стартовать. а можно более подробно?
что может быть причиной? как проверить исправность самой платы? 1 из плат стоит в одной(нулевой корзине) и все же не видит процессор.

Config:reset
Do you want to restart coupler now ! (y/n):y
Coupler will reset in 5 seconds !

Config:
Reset: Stop the coupler (ano 000000FF flag 00000000)
Flushing Black Memory Hole ...
Restarting Board...
###############################
# Mount BOOT FS #
###############################
File : 0060E8A0..0060EC5C -> 38C72A81 linux-boot.bin
File : 0060EC83..0068A1D8 -> 12940B41 vmlinux.bin.gz
File : 0068A1F9..0068A8C0 -> C483B65D rdimage.gz
File : 0068A8DC..0068A8DE -> 5BE3136B info.txt
###############################
# BOOT #
###############################
MAC Address: 00:80:9F:8B:D4:46
PCMS Code : 3BA23193ACJF06
Config.Word: 07628005
Code : 00600000..0060E87C
Boot FS : 0060E87C..0068A8DE
Heap : 00E00000..013FFFFF
Command : 005F0000..005F00FF
Residual : 00607DE0..00607E08 -> 005F0100..005F0128
Gunzip : 0060EC83..0068A1D8 -> 00000000..002130B8 vmlinux.bin.gz [Ok]
Gunzip : 0068A1F9..0068A8C0 -> 00488000..005F0000 rdimage.gz [Ok]
Ram disk : 00488000..005F0000
Linux : root=/dev/ram
###############################
# BOOT: booting the kernel #
###############################
Remove VMLINUX Memory Block [00000000..002A7000]
Black Memory Hole [01800000..02000000]
RamDisk Memory Block [00488000..005F0000]
Total memory = 32MB; using 128kB for hash table (at c02c0000)
Linux version 2.2.12/Alcatel build 1.12 (@colebu03) (gcc version 2.8.1) #45
Fri Apr 2 12:15:42 MEST 2004
Boot arguments: root=/dev/ram
INTIP BOARD Revision C : second 8Ko banks of DPRAM are reserved for QMC2 device
time_init: decrementer frequency = 600000000/60
Calibrating delay loop... 79.67 BogoMIPS
Global Linux Allocation OK [00000000..0031A800]
remove_mem_piece: bad overlap [2b7000,31b000) with [2b7000, 2c0000) [2e0000, 488
000) [5f0000, 1800000)
Memory: 19956k available (1044k kernel code, 2136k data, 0k init) [c0000000,c200
0000]
[31b000, 488000) [5f0000, 1800000)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
Starting kswapd v 1.5 úCPM UART driver version 0.02
ttyS00 at 0x07fc is a SMC
RAM disk driver initialized: 16 RAM disks of 4096K size
CPM ENET Version 0.1, 00:80:9f:8b:d4:46
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 1440 blocks [1 disk] into ram disk... done.
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 0k init

linux running ...
Seting BAT1 to disable physical R/W access

Create TTY device
Monitoring activated

FPGA programming with new binary...Ok
00000001-000001AB: Trace ok
00000002-000001AC: Boot : Data boot OK [Nb 0, Nw 0, Bad 0]
Config : Configuration OK
00000003-000001AD: FSK : fastsk init done
ResetMon : Save Registers to BOOT2APPLI memory area
ResetMon : Clear Reset status register
Create EthMon object
Create FastPing object
00000004-0000020E: Application Descriptor at address 0xc19ffeb8







------------------------------------------------------------------------------

Logical Board : INTIP A Boot

Physical Board : Revision 2 = AC (MPC8250 40MHz, V36, Alize V24 cable)
MuP : Version 8081 Revision 1014

Boot/download version : intip _06.10 _29Aug08_15h03

------------------------------------------------------------------------------

         ---> Hit ENTER key to suspend coupler boot process <---
INTIP:
                    5 sec left before starting coupler
                    4 sec left before starting coupler
                    3 sec left before starting coupler
                    2 sec left before starting coupler
                    1 sec left before starting coupler


X Starting Coupler






00000005-000006C4: MngtC1cpl : WAIT FOR C1 CLOCK
00000006-000006C4: MngtC1cpl : C1 CLOCK PRESENT
00000007-000006C4: C1:start_broadcasting
00000008-000006C4: CPU found on link 21
00000009-000006C4: Board Add Rq -> CPU
0000000A-000006C4: BOARD_ADR_RSP cold in cold Init
0000000B-000006C4: ConfigIP : Discovering our IP Address
0000000C-000006C8: ConfigIP : using DSCP
0000000D-000006C8: ConfigIP : default DSCP set to 0x2E
0000000E-000006C8: ConfigIP : Start Ethernet Link ...
0000000F-000006C8: EthMon : New ethernet abilities set [ 10MBps 100MBps Half ]
00000010-000006C8: EthMon : Autonegociation mode will be used
00000011-000006C8: EthMon : Lauch Ethernet Phyter
00000012-000006C8: EthMon : Ethernet Phyter ready
00000013-000006C8: EthMon : Start Auto-Negotiation ...
(Unexpected) Message:18 15 49 00 02 0F 00 11 08 FE 91
(Unexpected) Message:01 11 19 00 02 0F 00 11 08 FE 88
00000014-00000859: EthMon : Auto-Negotiation process complete (BMCR=0x1000, PHYS
TS=0x0E21) (True Auto-Negotiation)
00000015-00000859: EthMon : Speed set to 100MBps (Auto-sense)
00000016-00000859: EthMon : Duplex set to Half (Auto-neg)
00000017-00000859: EthMon : Wait for Link Up ...
00000018-00000859: EthMon : Link Up
00000019-00000859: ConfigIP : Startup of Ethernet Link succeed
0000001A-00000859: ConfigIP : IP Address : 10.250. 1. 50
0000001B-00000859: ConfigIP : IP Subnet Mask : 255.255.255. 0
0000001C-00000859: ConfigIP : IP Default Router : 10.250. 1. 1
0000001D-0000085A: ConfigIP : Query Default Router 10.250. 1. 1 using ICMP EC
HO REQUEST .....................
0000001E-000018D6: ConfigIP : Ethernet check success..........
0000001F-000020B1: ConfigIP : No response fr om Default Router [fsk status=0x01]
00000020-000020B1: Do not download lanpbx.cfg for role INTIP-A
00000021-000020B1: Simulate lanpbx.cfg for role INTIP-A
00000022-000020B1: created lanpbx file contents TYPE=A4400 VERSION=1 IP_DOWNLOAD
=10.250.1.3 IP_CPU1=10.250.1.3

00000023-000020B1: LANPBX : SEARCH OF THE GOOD CPU FR OM LANPBX.CFG
00000024-000020B1: LANPBX : contents of the line 1 of lanpbx.cfg :
00000025-000020B1: IP_DOWNLOAD= 10.250.1.3
00000026-000020B1: IP_DOWNLOAD_RD= None
00000027-000020B1: IP_CPU1= 10.250.1.3
00000028-000020B1: IP_CPU2= None
00000029-000020B1: BININTIP : Download of the binary [Current size lim it : 1024K
Bytes]
0000002A-000020B1: SEARCH FOR CPU : Try to start with cpu 10.250.1.3 (tftp clien
t number 0 try to download file 'binintip')
0000002B-00005386: SEARCH FOR CPU : cpu 10.250.1.3 deny INTIP board (tftp server
return error = 11)
0000002C-00005386: : "No Error Message"

=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
=-=-=-=-=-=-=-=-=

INTIP fails to start

Event : CPU search step failed

Diagnosis :
- INTIP board failed to locate the main CPU.

Checklist :
- Check lanpbx.cfg file content
- Check that Ethernet address and Crystal number are declared in database of th
e CPU
- Check that the CPU can ping INTIP board when this message is just displayed

=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
=-=-=-=-=-=-=-=-=
0000002D-00005386: SEARCH FOR CPU : We have not found the cpu (tftp server not f
ound)
Reset: Stop the coupler (ano 000000FF save 00000000) <0>
Flushing Black Memory Hole ...
Restarting Board...
###############################
# Mount BOOT FS #
###############################
File : 0060E8A0..0060EC5C -> 38C72A81 linux-boot.bin
File : 0060EC83..0068A1D8 -> 12940B41 vmlinux.bin.gz
File : 0068A1F9..0068A8C0 -> C483B65D rdimage.gz
File : 0068A8DC..0068A8DE -> 5BE3136B info.txt
###############################
# BOOT #
###############################
MAC Address: 00:80:9F:8B:D4:46
PCMS Code : 3BA23193ACJF06
Config.Word: 07628005
Code : 00600000..0060E87C
Boot FS : 0060E87C..0068A8DE
Heap : 00E00000..013FFFFF
Command : 005F0000..005F00FF
Residual : 00607DE0..00607E08 -> 005F0100..005F0128
Gunzip : 0060EC83..0068A1D8 -> 00000000..002130B8 vmlinux.bin.gz [Ok]
Gunzip : 0068A1F9..0068A8C0 -> 00488000..005F0000 rdimage.gz [Ok]
Ram disk : 00488000..005F0000
Linux : root=/dev/ram
###############################
# BOOT: booting the kernel #
###############################
Remove VMLINUX Memory Block [00000000..002A7000]
Black Memory Hole [01800000..02000000]
RamDisk Memory Block [00488000..005F0000]
Total memory = 32MB; using 128kB for hash table (at c02c0000)
Linux version 2.2.12/Alcatel build 1.12 (@colebu03) (gcc version 2.8.1) #45
Fri Apr 2 12:15:42 MEST 2004
Boot arguments: root=/dev/ram
INTIP BOARD Revision C : second 8Ko banks of DPRAM are reserved for QMC2 device
time_init: decrementer frequency = 600000000/60
Calibrating delay loop... 79.67 BogoMIPS
Global Linux Allocation OK [00000000..0031A800]
remove_mem_piece: bad overlap [2b7000,31b000) with [2b7000, 2c0000) [2e0000, 488
000) [5f0000, 1800000)
Memory: 19956k available (1044k kernel code, 2136k data, 0k init) [c0000000,c200
0000]
[31b000, 488000) [5f0000, 1800000)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
Starting kswapd v 1.5 úCPM UART driver version 0.02
ttyS00 at 0x07fc is a SMC
RAM disk driver initialized: 16 RAM disks of 4096K size
CPM ENET Version 0.1, 00:80:9f:8b:d4:46
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 1440 blocks [1 disk] into ram disk... done.
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 0k init

linux running ...
Seting BAT1 to disable physical R/W access

Create TTY device
Monitoring activated

FPGA programming with new binary...Ok
00000001-000001AB: Trace ok
00000002-000001AC: Boot : Data boot OK [Nb 0, Nw 0, Bad 0]
Config : Configuration OK
00000003-000001AD: FSK : fastsk init done
ResetMon : Save Registers to BOOT2APPLI memory area
ResetMon : Clear Reset status register
Create EthMon object
Create FastPing object
00000004-0000020E: Application Descriptor at address 0xc19ffeb8







------------------------------------------------------------------------------

Logical Board : INTIP A Boot

Physical Board : Revision 2 = AC (MPC8250 40MHz, V36, Alize V24 cable)
MuP : Version 8081 Revision 1014

Boot/download version : intip _06.10 _29Aug08_15h03

------------------------------------------------------------------------------

         ---> Hit ENTER key to suspend coupler boot process <---
INTIP:
                    5 sec left before starting coupler
                    4 sec left before starting coupler
                    3 sec left before starting coupler
                    2 sec left before starting coupler
                    1 sec left before starting coupler


X Starting Coupler






00000005-000006C4: MngtC1cpl : WAIT FOR C1 CLOCK
00000006-000006C4: MngtC1cpl : C1 CLOCK PRESENT
00000007-000006C4: C1:start_broadcasting
00000008-000006C4: CPU found on link 21
00000009-000006C4: Board Add Rq -> CPU
0000000A-000006C4: BOARD_ADR_RSP cold in cold Init
0000000B-000006C4: ConfigIP : Discovering our IP Address
0000000C-000006C8: ConfigIP : using DSCP
0000000D-000006C8: ConfigIP : default DSCP set to 0x2E
0000000E-000006C8: ConfigIP : Start Ethernet Link ...
0000000F-000006C8: EthMon : New ethernet abilities set [ 10MBps 100MBps Half ]
00000010-000006C8: EthMon : Autonegociation mode will be used
00000011-000006C8: EthMon : Lauch Ethernet Phyter
00000012-000006C8: EthMon : Ethernet Phyter ready
00000013-000006C8: EthMon : Start Auto-Negotiation ...
(Unexpected) Message:18 15 49 00 02 0F 00 11 08 FE 91
(Unexpected) Message:01 11 19 00 02 0F 00 11 08 FE 88
00000014-00000859: EthMon : Auto-Negotiation process complete (BMCR=0x1000, PHYS
TS=0x0E21) (True Auto-Negotiation)
00000015-00000859: EthMon : Speed set to 100MBps (Auto-sense)
00000016-00000859: EthMon : Duplex set to Half (Auto-neg)
00000017-00000859: EthMon : Wait for Link Up ...
00000018-00000859: EthMon : Link Up
00000019-00000859: ConfigIP : Startup of Ethernet Link succeed
0000001A-00000859: ConfigIP : IP Address : 10.250. 1. 50
0000001B-00000859: ConfigIP : IP Subnet Mask : 255.255.255. 0
0000001C-00000859: ConfigIP : IP Default Router : 10.250. 1. 1
0000001D-0000085A: ConfigIP : Query Default Router 10.250. 1. 1 using ICMP EC
HO REQUEST .....................
0000001E-000018D6: ConfigIP : Ethernet check success..........
0000001F-000020B1: ConfigIP : No response from Default Router [fsk status=0x01]
00000020-000020B1: Do not download lanpbx.cfg for role INTIP-A
00000021-000020B1: Simulate lanpbx.cfg for role INTIP-A
00000022-000020B1: created lanpbx file contents TYPE=A4400 VERSION=1 IP_DOWNLOAD
=10.250.1.3 IP_CPU1=10.250.1.3

00000023-000020B1: LANPBX : SEARCH OF THE GOOD CPU FROM LANPBX.CFG
00000024-000020B1: LANPBX : contents of the line 1 of lanpbx.cfg :
00000025-000020B1: IP_DOWNLOAD= 10.250.1.3
00000026-000020B1: IP_DOWNLOAD_RD= None
00000027-000020B1: IP_CPU1= 10.250.1.3
00000028-000020B1: IP_CPU2= None
00000029-000020B1: BININTIP : Download of the binary [Current size lim it : 1024K
Bytes]
0000002A-000020B1: SEARCH FOR CPU : Try to start with cpu 10.250.1.3 (tftp clien
t number 0 try to download file 'binintip')
0000002B-00005386: SEARCH FOR CPU : cpu 10.250.1.3 deny INTIP board (tftp server
return error = 11)
0000002C-00005386: : "No Error Message"

=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
=-=-=-=-=-=-=-=-=

INTIP fails to start

Event : CPU search step failed

Diagnosis :
- INTIP board failed to locate the main CPU.

Checklist :
- Check lanpbx.cfg file content
- Check that Ethernet address and Crystal number are declared in database of th
e CPU
- Check that the CPU can ping INTIP board when this message is just displayed

=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
=-=-=-=-=-=-=-=-=
0000002D-00005386: SEARCH FOR CPU : We have not found the cpu (tftp server not f
ound)