Добрый день!
Прошу совета в решении проблемы с АТС. Исправно работала на объекте примерно с 2009-2010 года. После переезда в новое здание, что-то с ней случилось. Полностью не загружается, предлагает зайти в консоль.
Вот лог загрузки:
INIT: Switching to runlevel: 6
INIT: Saving e-mgd configuration files ...
Saving System Clock in Hardware Clock ...
No backtrace
Sending all processes the TERM signal...
Sending all processes the KILL signal..
Unmounting file systems
Please stand by while rebooting the system...
Restarting system.
ShutOK cleared!
щ+Alize BIOS Monitor
*** BIOS Version 3EH30227GQAA bios100/010.014 ***
*** Generated on Mar/5/2008 at 14:05 ***
memory test started lng=133169152 with 0
running flash(soldered=1 socket=0)=1,BIOScase:4,BIOSv24:0,verrou=1,algoNOR=1,siz
e=1,base=3FF80000
DIMM characteristics->: JEDEC Manu ID:к,......
Memory type(EDO,FPM..):0x 4
# of row address:13
# of col address 9
# of module row 1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI:scan_bus for bus 0
PCI:bus=00h,devfn=00h ,[vendor:device]=[1022h/3000h]
PCI:bus=00h,devfn=60h ,[vendor:device]=[100Bh/0020h]
PCI:bus=00h,devfn=98h ,[vendor:device]=[1064h/2101h]
PCI:scan_buses with 00h secondary buses
PCI:command = 3FFH for device 00:00
PCI: Assigning I/O space FC00-FCFF for 00:60 BAR= 10
PCI:Assign memory space BFFFF000H to BFFFFFFFH for device 00:60
PCI:command = 3FFH for device 00:60
PCI:Assign memory space BFFFD000H to BFFFDFFFH for device 00:98
PCI: Assigning I/O space FD00-FD1F for 00:98 BAR= 14
PCI: Unable to handle I/O allocation for 00:98 (FF04) BAR= 18
PCI:command = 3FFH for device 00:98
assigning irq10 to xchange
B0 = 17
DRCTMCTL = 1E
DRCCTL = 8
DBCTL = 11
Set external RTC
Set Internal RTC
No external RTC detected
gpbus sig timing : 0-2-1-2-1-2!
CMOS is available
Xchange PCI mem base OK: 0,mbx= BFFFD000
dsp_accesses.stat_ctrl= FD00
Xchange PCI IO base OK: 0
Xchange irq OK: A
PCI command read for natsemi : 347
PCI Master Bit Setting...
pci_command set to: 357
0 80 9F 82 63 DE ,IRQ 12.on interrupt pin:2
eth0: Transceiver status 0x 7869 advertising 5E1
Flashfx version:700.014.700c
Flash 2Gbit Support activated !!
GC-forced on Soft Error activated !!
NAND Flash Comfiguration:
CPU size : 128 MBytes
free spare blocks: 37
NAND Flash Details:
chip #0 : Type=NAND01GW3B Id=20F1H Size=128(MBytes) Unit size=131072
Page Size=2048
time :sec=34,min=26,hour=17,DoW= 5,date=13,Month=10,year=16
time :sec=38,min=26,hour=17,DoW= 5,date=13,Month=10,year=16
ALIZE informations :
Memory Detected : 131072 Ko
Flash Detected
DaughterBoard Detected
DSP Voip Found : 1
XCHANGE Detected
XCHANGE Chip Initialization OK
Ethernet Found : 1
Ethernet Chip Initialization OK
Hard Disk Not Detected
PCM11 selected
CPU at 133 mhz
check lock RTC
value of DIL switch 2
YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW
!
BATMODE testing
Static Boot from hard disk #0(3)
unable to boot on DISK
Static Boot from No Boot Device selected(0)
Static Boot from flash NAND mother(1)
BOOT Sector Found on NAND Flash Drive #0
Shutdown of the interface 0 = 0
init ethernet interface 1 not done
Watch dog started
Linux version 2.2.18-rtl (che_int@csbu176) (gcc version 2.95.2 19991024 (release
)) #1 Tue Mar 25 20:36:39 IST 2008
Calibrating delay loop... 65.74 BogoMIPS
Memory: 122808k/131072k available (644k kernel code, 408k reserved, 1584k data,
36k init)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
ShutOK cleared!
Dentry hash table entries: 16384 (order 5, 128k)
Buffer cache hash table entries: 131072 (order 7, 512k)
Page cache hash table entries: 32768 (order 5, 128k)
CPU: AMD 486 DX/4-WB stepping 04
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 131072 bhash 65536)
802.1Q VLAN Support v1.0 © 2000 Ben Greear (GPL)
vlan Initialization complete.
Starting kswapd v 1.5
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
RAM disk driver initialized: 16 RAM disks of 20480K size
RAMDISK: Compressed image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 36k freed
Warning: unable to open an initial console.
Initial console created for init
RTLinux Extensions Loaded ()
Starting watchdog timer daemon using /dev/rtf3
modprobe: modprobe: Can't locate module char-major-4
INIT: version 2.78 booting
Remounting root read-write....
modprobe: modprobe: Can't locate module char-major-4
e-mgd board found - setting up ramdisk
Remount - Forces the media to be remounted
Datalight FlashFx
V4.06.500 Back ported to OmniPCX MediaGateway
Copyright © 1993-2005
Patent US#5860082
Disk Remounted
e2fsck 1.19, 13-Jul-2000 for EXT2 FS 0.5b, 95/08/09
/dev/fla: clean, 121/30360 files, 15385/121396 blocks
/dev/fla on /mnt/flash type ext2 (rw)
Set initial public keys
/mnt/flash/local/ifcfg-eth0: OK
Find ip configuration in /mnt/flash/local/
/mnt/flash/local/startup.cfg: OK
INIT: Entering runlevel: 3 in
Trying to map the io space of the board(=1). Wait 10 sec...
Compression daughter board type [MADA]
mada_3 DSP daughter board
e-MGD version 43.15.2
Media Gateway Software R8.0 loading ...
No password file found - using default password list
Starting /etc/rcS.d/01fifos
Starting /etc/rcS.d/05syslog
Starting /etc/rcS.d/10network
Starting /etc/rcS.d/90init
BIOS updater is now working ... getting current version information
Check if we need to upd ate with bios 3EH30227GQAA bios100/010.014 ...
Reboot after bios update is enabled...
----- RetrieveFlashNorInfo -----
NOR VERSION : Bios Version in soldered NOR flash : 3EH30227GQAA bios100/010
.014 len = 28
- Flash Nor Informations -
Flash AMD
Size : 512 Kbytes
Number of sectors : 11
----- CompareBiosVersions -----
CURRENT=010.014 FILE=0eth0 : chip revision 0403.
10.014
*******************************
* NO bios Update is necessary *
*******************************
Basic registers of MII PHY #1: 2000 784d 2000 5c21 04a1 45e1 0007 2801.
Link status: active.
Authentification lanpbx FAILED --> see /var/log/init
Loading modules - please wait ...
watchdogd now in real time mode
DSP Manager OK
Fast Socket Initialization... Ok
init_module:no param_8021q=-1 is used
============ continue_rack_init ==============
DIL SWITCH VALUE = 0x2
1024 Ko - BUFFER ALLOCATED
MGD - RACK CONSTRUCTION
@ MAC : 00:80:9f:82:63:de
@ IP : 10.x.y.167
net mask : 255.255.255.0
gateway : 10.x.y.118
CS role address : 10.x.y.166
CS redundancy role address : 0.0.0.0
Passive Comm server address: 10.x.y.166
default crystal number : 3 (Dynamic allocation)
vlan id : -1
default priority : 0
default dscp : 0
duplex mode : negociation (half duplex only)
download binary timeout : 1200
Module MG Loaded:no vlan se t
watchdogd now in normal mode
RTLinux System Load 1.00
init_module GPA
->insmod GPA
Module GPA loaded
Module APA loaded
Module SLAC loaded
Module DDI loaded
Module UAI loaded
Module SLI loaded
Insert INTX module
Insert ISDN module
Module BRA loaded
Module PRA loaded
Module PRACCS loaded
Module PRA_T1CAS loaded
Module PRA_E1CAS loaded
->init_module eMGA ==> eMGD_eMGA & eMGD_GPA module types created !
Module eMGD_eMGA loaded
Module eMGD_GPA loaded
Module MIX loaded
Module ATL loaded
Module RESCUE loaded
PUC_device registered
Module DPNSS loaded
Module DSPx_LOAD loaded
Module UASIM loaded
====== record_country_correspondaces
====== record_default_country 0 (DEFAULT COUNTRY : HU based with Poland tones)
eth0 : chip revision 0403.
Warning: couldn't reach specified router
binmg : this is Media Gateway Software R8.0 for E-MGD version 43.15.2 built on 2
8 May 08 17 hours 17 min for r_mg_appli_43.15.2
Downloading /DHS3bin/downbin/emg/binmg from 10.x.y.166
/usr/bin/binmg_download: download_binary binmg failed
/usr/bin/binmg_download: download of binmg failed: file not found on server or b
ad transfer or file corrupted
/usr/bin/binmg_download: sleeping 5s then retrying...
Downloading /DHS3bin/downbin/emg/binmg from 10.x.y.166
/usr/bin/binmg_download: download_binary binmg failed
/usr/bin/binmg_download: download of binmg failed: file not found on server or b
ad transfer or file corrupted
/usr/bin/binmg_download: sleeping 5s then retrying...
Downloading /DHS3bin/downbin/emg/binmg from 10.x.y.166
/usr/bin/binmg_download: download_binary binmg failed
/usr/bin/binmg_download: too many retries, giving up
binmg download failed after 3 retries
loading MCV module - please wait ...
DSP firmware successfully read in flash (size=754156)
/mnt/flash/local/startemg: OK
Startup completed - awaiting user login ...
Starting /etc/rcS.d/99crond
Start VG_PROCESS using /dev/rtf5 and /dev/rtf4
Trace OFF
Welcome to PeeWeeLinux
WARNING: root account has no password
Use 'passwd root' to enter a valid password
Посоветуйте, пожалуйста, что может случиться с АТС. Патчкорда на станции целые, на всякий случай поменял на 6-ю категорию.
Заранее благодарю!
Прошу совета в решении проблемы с АТС. Исправно работала на объекте примерно с 2009-2010 года. После переезда в новое здание, что-то с ней случилось. Полностью не загружается, предлагает зайти в консоль.
Вот лог загрузки:
INIT: Switching to runlevel: 6
INIT: Saving e-mgd configuration files ...
Saving System Clock in Hardware Clock ...
No backtrace
Sending all processes the TERM signal...
Sending all processes the KILL signal..
Unmounting file systems
Please stand by while rebooting the system...
Restarting system.
ShutOK cleared!
щ+Alize BIOS Monitor
*** BIOS Version 3EH30227GQAA bios100/010.014 ***
*** Generated on Mar/5/2008 at 14:05 ***
memory test started lng=133169152 with 0
running flash(soldered=1 socket=0)=1,BIOScase:4,BIOSv24:0,verrou=1,algoNOR=1,siz
e=1,base=3FF80000
DIMM characteristics->: JEDEC Manu ID:к,......
Memory type(EDO,FPM..):0x 4
# of row address:13
# of col address 9
# of module row 1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI:scan_bus for bus 0
PCI:bus=00h,devfn=00h ,[vendor:device]=[1022h/3000h]
PCI:bus=00h,devfn=60h ,[vendor:device]=[100Bh/0020h]
PCI:bus=00h,devfn=98h ,[vendor:device]=[1064h/2101h]
PCI:scan_buses with 00h secondary buses
PCI:command = 3FFH for device 00:00
PCI: Assigning I/O space FC00-FCFF for 00:60 BAR= 10
PCI:Assign memory space BFFFF000H to BFFFFFFFH for device 00:60
PCI:command = 3FFH for device 00:60
PCI:Assign memory space BFFFD000H to BFFFDFFFH for device 00:98
PCI: Assigning I/O space FD00-FD1F for 00:98 BAR= 14
PCI: Unable to handle I/O allocation for 00:98 (FF04) BAR= 18
PCI:command = 3FFH for device 00:98
assigning irq10 to xchange
B0 = 17
DRCTMCTL = 1E
DRCCTL = 8
DBCTL = 11
Set external RTC
Set Internal RTC
No external RTC detected
gpbus sig timing : 0-2-1-2-1-2!
CMOS is available
Xchange PCI mem base OK: 0,mbx= BFFFD000
dsp_accesses.stat_ctrl= FD00
Xchange PCI IO base OK: 0
Xchange irq OK: A
PCI command read for natsemi : 347
PCI Master Bit Setting...
pci_command set to: 357
0 80 9F 82 63 DE ,IRQ 12.on interrupt pin:2
eth0: Transceiver status 0x 7869 advertising 5E1
Flashfx version:700.014.700c
Flash 2Gbit Support activated !!
GC-forced on Soft Error activated !!
NAND Flash Comfiguration:
CPU size : 128 MBytes
free spare blocks: 37
NAND Flash Details:
chip #0 : Type=NAND01GW3B Id=20F1H Size=128(MBytes) Unit size=131072
Page Size=2048
time :sec=34,min=26,hour=17,DoW= 5,date=13,Month=10,year=16
time :sec=38,min=26,hour=17,DoW= 5,date=13,Month=10,year=16
ALIZE informations :
Memory Detected : 131072 Ko
Flash Detected
DaughterBoard Detected
DSP Voip Found : 1
XCHANGE Detected
XCHANGE Chip Initialization OK
Ethernet Found : 1
Ethernet Chip Initialization OK
Hard Disk Not Detected
PCM11 selected
CPU at 133 mhz
check lock RTC
value of DIL switch 2
YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW
!
BATMODE testing
Static Boot from hard disk #0(3)
unable to boot on DISK
Static Boot from No Boot Device selected(0)
Static Boot from flash NAND mother(1)
BOOT Sector Found on NAND Flash Drive #0
Shutdown of the interface 0 = 0
init ethernet interface 1 not done
Watch dog started
Linux version 2.2.18-rtl (che_int@csbu176) (gcc version 2.95.2 19991024 (release
)) #1 Tue Mar 25 20:36:39 IST 2008
Calibrating delay loop... 65.74 BogoMIPS
Memory: 122808k/131072k available (644k kernel code, 408k reserved, 1584k data,
36k init)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
ShutOK cleared!
Dentry hash table entries: 16384 (order 5, 128k)
Buffer cache hash table entries: 131072 (order 7, 512k)
Page cache hash table entries: 32768 (order 5, 128k)
CPU: AMD 486 DX/4-WB stepping 04
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 131072 bhash 65536)
802.1Q VLAN Support v1.0 © 2000 Ben Greear (GPL)
vlan Initialization complete.
Starting kswapd v 1.5
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
RAM disk driver initialized: 16 RAM disks of 20480K size
RAMDISK: Compressed image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 36k freed
Warning: unable to open an initial console.
Initial console created for init
RTLinux Extensions Loaded ()
Starting watchdog timer daemon using /dev/rtf3
modprobe: modprobe: Can't locate module char-major-4
INIT: version 2.78 booting
Remounting root read-write....
modprobe: modprobe: Can't locate module char-major-4
e-mgd board found - setting up ramdisk
Remount - Forces the media to be remounted
Datalight FlashFx
V4.06.500 Back ported to OmniPCX MediaGateway
Copyright © 1993-2005
Patent US#5860082
Disk Remounted
e2fsck 1.19, 13-Jul-2000 for EXT2 FS 0.5b, 95/08/09
/dev/fla: clean, 121/30360 files, 15385/121396 blocks
/dev/fla on /mnt/flash type ext2 (rw)
Set initial public keys
/mnt/flash/local/ifcfg-eth0: OK
Find ip configuration in /mnt/flash/local/
/mnt/flash/local/startup.cfg: OK
INIT: Entering runlevel: 3 in
Trying to map the io space of the board(=1). Wait 10 sec...
Compression daughter board type [MADA]
mada_3 DSP daughter board
e-MGD version 43.15.2
Media Gateway Software R8.0 loading ...
No password file found - using default password list
Starting /etc/rcS.d/01fifos
Starting /etc/rcS.d/05syslog
Starting /etc/rcS.d/10network
Starting /etc/rcS.d/90init
BIOS updater is now working ... getting current version information
Check if we need to upd ate with bios 3EH30227GQAA bios100/010.014 ...
Reboot after bios update is enabled...
----- RetrieveFlashNorInfo -----
NOR VERSION : Bios Version in soldered NOR flash : 3EH30227GQAA bios100/010
.014 len = 28
- Flash Nor Informations -
Flash AMD
Size : 512 Kbytes
Number of sectors : 11
----- CompareBiosVersions -----
CURRENT=010.014 FILE=0eth0 : chip revision 0403.
10.014
*******************************
* NO bios Update is necessary *
*******************************
Basic registers of MII PHY #1: 2000 784d 2000 5c21 04a1 45e1 0007 2801.
Link status: active.
Authentification lanpbx FAILED --> see /var/log/init
Loading modules - please wait ...
watchdogd now in real time mode
DSP Manager OK
Fast Socket Initialization... Ok
init_module:no param_8021q=-1 is used
============ continue_rack_init ==============
DIL SWITCH VALUE = 0x2
1024 Ko - BUFFER ALLOCATED
MGD - RACK CONSTRUCTION
@ MAC : 00:80:9f:82:63:de
@ IP : 10.x.y.167
net mask : 255.255.255.0
gateway : 10.x.y.118
CS role address : 10.x.y.166
CS redundancy role address : 0.0.0.0
Passive Comm server address: 10.x.y.166
default crystal number : 3 (Dynamic allocation)
vlan id : -1
default priority : 0
default dscp : 0
duplex mode : negociation (half duplex only)
download binary timeout : 1200
Module MG Loaded:no vlan se t
watchdogd now in normal mode
RTLinux System Load 1.00
init_module GPA
->insmod GPA
Module GPA loaded
Module APA loaded
Module SLAC loaded
Module DDI loaded
Module UAI loaded
Module SLI loaded
Insert INTX module
Insert ISDN module
Module BRA loaded
Module PRA loaded
Module PRACCS loaded
Module PRA_T1CAS loaded
Module PRA_E1CAS loaded
->init_module eMGA ==> eMGD_eMGA & eMGD_GPA module types created !
Module eMGD_eMGA loaded
Module eMGD_GPA loaded
Module MIX loaded
Module ATL loaded
Module RESCUE loaded
PUC_device registered
Module DPNSS loaded
Module DSPx_LOAD loaded
Module UASIM loaded
====== record_country_correspondaces
====== record_default_country 0 (DEFAULT COUNTRY : HU based with Poland tones)
eth0 : chip revision 0403.
Warning: couldn't reach specified router
binmg : this is Media Gateway Software R8.0 for E-MGD version 43.15.2 built on 2
8 May 08 17 hours 17 min for r_mg_appli_43.15.2
Downloading /DHS3bin/downbin/emg/binmg from 10.x.y.166
/usr/bin/binmg_download: download_binary binmg failed
/usr/bin/binmg_download: download of binmg failed: file not found on server or b
ad transfer or file corrupted
/usr/bin/binmg_download: sleeping 5s then retrying...
Downloading /DHS3bin/downbin/emg/binmg from 10.x.y.166
/usr/bin/binmg_download: download_binary binmg failed
/usr/bin/binmg_download: download of binmg failed: file not found on server or b
ad transfer or file corrupted
/usr/bin/binmg_download: sleeping 5s then retrying...
Downloading /DHS3bin/downbin/emg/binmg from 10.x.y.166
/usr/bin/binmg_download: download_binary binmg failed
/usr/bin/binmg_download: too many retries, giving up
binmg download failed after 3 retries
loading MCV module - please wait ...
DSP firmware successfully read in flash (size=754156)
/mnt/flash/local/startemg: OK
Startup completed - awaiting user login ...
Starting /etc/rcS.d/99crond
Start VG_PROCESS using /dev/rtf5 and /dev/rtf4
Trace OFF
Welcome to PeeWeeLinux
WARNING: root account has no password
Use 'passwd root' to enter a valid password
Посоветуйте, пожалуйста, что может случиться с АТС. Патчкорда на станции целые, на всякий случай поменял на 6-ю категорию.
Заранее благодарю!