Попробовали прошить INTIP3A. В процессе прошивки зависает и уходит в циклический ребут.
Press ^B^I to enter into the Bios menu 8
1- Load from Hard disk
2- Load from SDcard
3- Load from Ethernet
4- Load from Hard disk & bootp
5- Load from SDcard & bootp
6- Display MAC addresses , CPUID and Serial Number
7- Reset
Your choice followed by carriage return : 3
Booting from NETWORK BOOTP
Hit any key to stop autoboot: 0
## Booting image at ff839398 ...
Image Name: gpioinit.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 2185 Bytes = 2.1 kB
Load Address: 00200000
Entry Point: 00200620
Verifying Checksum ... OK
OK
Watchdog Started
Speed: 100, full duplex
Using TSEC0 device
BOOTP broadcast request 1 in progress ---> 00:80:9f:d8:d9:ae
Using TSEC0 device
TFTP from server 192.168.61.15; our IP address is 192.168.61.16
Filename '/DHS3bin/downbin/intip3/binintip3start'.
Load address: 0x100000
Loading: #
done
Bytes transferred = 689 (2b1 hex)
## Executing script at 00100000
Speed: 100, full duplex
Using TSEC0 device
TFTP from server 192.168.61.15; our IP address is 192.168.61.16
Filename '/DHS3bin/downbin/intip3/binintip3linux'.
Load address: 0x4000000
Loading: #################################################################
#################################################################
###########
done
Bytes transferred = 2004142 (1e94ae hex)
Speed: 100, full duplex
Using TSEC0 device
TFTP from server 192.168.61.15; our IP address is 192.168.61.16
Filename '/DHS3bin/downbin/intip3/binintip3rdimg'.
Load address: 0x6000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
##############################################
done
Bytes transferred = 10866759 (a5d047 hex)
## Booting image at 04000000 ...
Image Name: Linux-2.6.23.17-020.001
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 2004078 Bytes = 1.9 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at 06000000 ...
Image Name: dhs3ngp_OXE_NGP_7.0_subint_view
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 10866695 Bytes = 10.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Booting using the fdt at 0x5800000
Loading Ramdisk to 0f542000, end 0ff9f007 ... OK
Loading Device Tree to 007fd000, end 007fefff ... OK
setup_arch: bootmem
ale8377_intip3_setup_arch()
arch: exit
Using Alcatel-Lucent 8377 INTIP3 machine description
Linux version 2.6.23.17-020.001 (alize100@frillux) (gcc version 4.1.2) #1 PREEMP T Wed Oct 30 12:21:52 CET 2013
Found initrd at 0xcf542000:0xcff9f007
[MTD] Found 5 partitions in device-tree
Found MPC83xx PCI host bridge at 0x00000000e0008500. Firmware bus number: 0->0
Zone PFN ranges:
DMA 0 -> 65536
Normal 65536 -> 65536
HighMem 65536 -> 65536
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 65536
Built 1 zonelists in Zone order. Total pages: 65024
Kernel command line: root=/dev/ram console=ttyS0,9600 ip=192.168.61.16:192.168.6 1.15::255.255.255.0:OXE_1:eth0:off boot_from=bootp console_baudrate=9600 factory _mode=no
IPIC (128 IRQ sources) at fcffb700
PID hash table entries: 1024 (order: 10, 4096 bytes)
I-pipe 2.0-09: pipeline enabled.
console [kgdb0] enabled
Console: colour dummy device 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 244224k/262144k available (3988k kernel code, 17632k reserved, 160k data , 535k bss, 156k init)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Found MPC8377 (hardware revision 2.1)
Read ALE devices configuration from DeviceTree
PCI: Probing PCI hardware
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 10612k freed
prom_parse: Bad cell count for /soc@e0000000/mdio@24520/ethernet-phy@1
prom_parse: Bad cell count for /soc@e0000000/mdio@24520/ethernet-phy@2
Xenomai: system heap size: 16384 kB
I-pipe: Domain Xenomai registered.
Xenomai: hal/powerpc started.
Xenomai: init success
I-pipe: Domain IShield registered.
Xenomai: real-time nucleus v2.4.5 (Overdriver) loaded.
Xenomai: starting native API services.
Xenomai: starting POSIX services.
Xenomai: starting RTDM services.
Xenomai: starting RTAI emulator.
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0xe0004500 mem 0xd1002500 (irq = 20) is a 16550A
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0xe0004600 mem 0xd1004600 (irq = 21) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
Gianfar MII Bus: probed
eth0: Gianfar Ethernet Controller Version 1.3-skbr, 00:80:9f:d8:d9:ae
GFAR: SKB Handler initialized at CPU#0(max=32)
eth0: MTU = 1500 (frame size=1526, truesize=1808)
eth0: Running with NAPI disabled
eth0: 1024/256 RX/TX BD ring size
eth1: Gianfar Ethernet Controller Version 1.3-skbr, 00:80:9f:d8:d9:af
GFAR: SKB Handler initialized at CPU#0(max=32)
eth1: MTU = 1500 (frame size=1526, truesize=1808)
eth1: Running with NAPI disabled
eth1: 1024/256 RX/TX BD ring size
kgdboe: couldn't parse config at not_configured!
kgdboe: configuration incorrect - kgdboe not loaded.
Usage: kgdboe=[src-port]@[src-ip]/[dev],[tgt-port]@<tgt-ip>/<tgt-macaddr>
physmap platform flash device: 00200000 at ff800000
physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash.0: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition information
Creating 4 MTD partitions on "physmap-flash.0":
0x00000000-0x000e0000 : "firmware"
0x000e0000-0x00100000 : "hardware"
0x00110000-0x001f0000 : "fs"
0x001f0000-0x00200000 : "factory"
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
esdhc: Freescale Enhanced Secure Digital Host Controller driver
esdhc:slot0: SDCard is Full-Speed Capable (25 MHz)
esdhc:slot0: Invalid maximum block size, assuming 512
mmc0: ESDHC at 0xe002e000 irq 42 DMA
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
esdhc:slot0: clock 400000 Hz
esdhc:slot0: SDCard clock is now running at 1302083 Hz
get_cd (or) get_cd(host) is there...
esdhc:slot0: clock 25000000 Hz
esdhc:slot0: SDCard clock is now running at 23809523 Hz
mmc0: new SD card at address 0007
mmcblk0: mmc0:0007 SD01G 995328KiB
mmcblk0: p1
IP-Config: Complete:
device=eth0, addr=192.168.61.16, mask=255.255.255.0, gw=255.255.255.255,
host=OXE_1, domain=, nis-domain=(none),
bootserver=192.168.61.15, rootserver=192.168.61.15, rootpath=
Freeing unused kernel memory: 156k init
loop: module loaded
U-Boot 1.3.0-rc3 (Jan 12 2012 - 14:42:54) 3EH30350AAAS bootl100/000.018
Reset Status:
CPU: e300c4, MPC8377, Rev: 21 at 666.666 MHz, CSB: 333 MHz
I2C: ready
DRAM:
DDR DIMM: data bus width is 64 bit without ECC
DDRC ECC mode: OFF
DDR RAM: 256 MB
Ъ
U-Boot 1.3.0-rc3 (Jan 12 2012 - 14:42:54) 3EH30350AAAS bootl100/000.018
Reset Status: Check Stop, External/Internal Soft, External/Internal Hard
CPU: e300c4, MPC8377, Rev: 21 at 666.666 MHz, CSB: 333 MHz
I2C: ready
DRAM:
DDR DIMM: data bus width is 64 bit without ECC
DDRC ECC mode: OFF
DDR RAM: 256 MB
Пробовали несколько раз. Каждый раз то раньше, то позже подвисает и в циклический ребут.
Изменено: mtch - 18.04.2017 13:38:11
