Всё делаю так как сказал:
______________________________
| Цитата |
|---|
Sергей пишет:
1. Подключаетесь 2-мя способами: консольным шнурком к разъему config на CS и по локальной сети.
2. На компе запускаете PC Installer со всеми настройками.
3. На компе запускаете Hyper Terminal (9600-8-n-1).
4. Запускаете станцию и видете в терминалке процесс загрузки.
5. В какой-то момент появится надпись "You can strike Ctr+B...". В этот момент жмете Ctr+B, а затем Ctr+I.
6. На запрос пароля жмете Enter.
7. Появившемся меню выбираете Load from Ethernet.
8. В PC Installere появятся данные (MAC, имя файла и т.д.)
P.S. Иногда можно видеть в терминалке тфтп-запросы, на которые PC Installer не реагирует. В таком случае полезно сначала запустить станцию, а PC Installer запустить когда появится иконка подключения по сети. |
_______________________________
Но получается хрень.Вообщем не чего;)
В терминале выдает:
Memory type(EDO,FPM..):0x04
# of row address:13
# of col address 9
# of module row 1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI:scan_bus for bus 0
PCI:bus=00h,devfn=00h ,[vendor:device]=[1022h/3000h]
PCI:bus=00h,devfn=60h ,[vendor:device]=[100bh/0020h]
PCI:bus=00h,devfn=98h ,[vendor:device]=[1064h/2101h]
PCI:scan_buses with 00h secondary buses
PCI:command =000003ffH for device 00:00
PCI: Assigning I/O space fc00-fcff for 00:60 BAR=00000010
PCI:Assign memory space bffff000H to bfffffffH for device 00:60
PCI:command =000003ffH for device 00:60
PCI:Assign memory space bfffd000H to bfffdfffH for device 00:98
PCI: Assigning I/O space fd00-fd1f for 00:98 BAR=00000014
PCI: Unable to handle I/O allocation for 00:98 (ff04) BAR=00000018
PCI:command =000003ffH for device 00:98
assigning irq10 to xchange
B0 = 17
DRCTMCTL = 1e
DRCCTL = 08
DBCTL = 11
Set external RTC
Set Internal RTC
No external RTC detected
gpbus sig timing : 0-2-1-2-1-2!
CMOS is available
Xchange PCI mem base OK: 00000000
Xchange PCI IO base OK: 00000000
Xchange irq OK: 0a
PCI command read for natsemi : 00000347
PCI Master Bit Setting...
pci_command set to:0357
0000 0080 009f 0038 0050 0016 , IRQ 12.
eth0: Transceiver status 0x00007849 advertising 000005e1
Hard Disk #0 : WDC WD1200BEVE-00A0HT0 114473 Mo
Parameters :
Type 00000
Extended Type 00255
Sectors / track 00063
Landing Zone 00000
Control Byte 00000
Write Precomp 00000
Heads 00016
Nb of Cylinders 16383
HD size(cyl*sec by track*head*sector size) 08455 MO(decimal)
init nand set interupt
Flashfx version:520.001.001
Cannot mount flash drive No 0. Flash NAND may not be formatted !
Cannot mount flash drive No 0. Flash NAND may not be formatted !
NAND Flash Comfiguration:
CPU size : 32 MBytes
free spare blocks: 38
XMEM size : 0 MBytes
NAND Flash Details:
chip #0 : Type=TC58256 Id=9875H Size=32(MBytes) Unit size=16384 Page Size=5
12
time :sec=51,min=40,hour=08,DoW=03,date=01,Month=12,year=10
time :sec=54,min=40,hour=08,DoW=03,date=01,Month=12,year=10
ALIZE informations :
Memory Detected : 131072 Ko
Flash Detected
DaughterBoard Not Detected
XCHANGE Detected
XCHANGE Chip Initialization OK
Ethernet Found : 1
Ethernet Chip Initialization OK
Hard Disk Detected
Hard Disk Found : 1
DMA enabled
PCM11 selected
Back Panel NMI disabled
No HD trace
CPU at 133 mhz
check lock RTC
value of DIL switch 01
YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW
!
Static Boot from hard disk #0 (3)
Exc : GpИ‹Alize BIOS Monitor
*** BIOS Version 3EH30227EIAA bios100/008.033 ***
*** Generated on Nov/04/2004 at 14:51 ***
memory test started lng=133169152 with 0
running flash(soldered=1 socket=0)=1,BIOScase:4,BIOSv24:0,verrou=1,algoNOR=1,siz
e=1,base=3ff80000
Exc : Nmi
NMI :PIO5(SHUTOK) cleared
DIMM characteristics->: JEDEC Manu ID:к,яяяяяя
Memory type(EDO,FPM..):0x04
# of row address:13
# of col address 9
# of module row 1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI:scan_bus for bus 0
PCI:bus=00h,devfn=00h ,[vendor:device]=[1022h/3000h]
PCI:bus=00h,devfn=60h ,[vendor:device]=[100bh/0020h]
PCI:bus=00h,devfn=98h ,[vendor:device]=[1064h/2101h]
PCI:scan_buses with 00h secondary buses
PCI:command =000003ffH for device 00:00
PCI: Assigning I/O space fc00-fcff for 00:60 BAR=00000010
PCI:Assign memory space bffff000H to bfffffffH for device 00:60
PCI:command =000003ffH for device 00:60
PCI:Assign memory space bfffd000H to bfffdfffH for device 00:98
PCI: Assigning I/O space fd00-fd1f for 00:98 BAR=00000014
PCI: Unable to handle I/O allocation for 00:98 (ff04) BAR=00000018
PCI:command =000003ffH for device 00:98
assigning irq10 to xchange
B0 = 17
DRCTMCTL = 1e
DRCCTL = 08
DBCTL = 11
Set external RTC
Set Internal RTC
No external RTC detected
gpbus sig timing : 0-2-1-2-1-2!
CMOS is available
Xchange PCI mem base OK: 00000000
Xchange PCI IO base OK: 00000000
Xchange irq OK: 0a
PCI command read for natsemi : 00000347
PCI Master Bit Setting...
pci_command set to:0357
0000 0080 009f 0038 0050 0016 , IRQ 12.
eth0: Transceiver status 0x00007849 advertising 000005e1
Hard Disk #0 : WDC WD1200BEVE-00A0HT0 114473 Mo
Parameters :
Type 00000
Extended Type 00255
Sectors / track 00063
Landing Zone 00000
Control Byte 00000
Write Precomp 00000
Heads 00016
Nb of Cylinders 16383
HD size(cyl*sec by track*head*sector size) 08455 MO(decimal)
init nand set interupt
Flashfx version:520.001.001
Cannot mount flash drive No 0. Flash NAND may not be formatted !
Cannot mount flash drive No 0. Flash NAND may not be formatted !
NAND Flash Comfiguration:
CPU size : 32 MBytes
free spare blocks: 38
XMEM size : 0 MBytes
NAND Flash Details:
chip #0 : Type=TC58256 Id=9875H Size=32(MBytes) Unit size=16384 Page Size=5
12
time :sec=28,min=41,hour=08,DoW=03,date=01,Month=12,year=10
time :sec=32,min=41,hour=08,DoW=03,date=01,Month=12,year=10
ALIZE informations :
Memory Detected : 131072 Ko
Flash Detected
DaughterBoard Not Detected
XCHANGE Detected
XCHANGE Chip Initialization OK
Ethernet Found : 1
Ethernet Chip Initialization OK
Hard Disk Detected
Hard Disk Found : 1
DMA enabled
PCM11 selected
Back Panel NMI disabled
No HD trace
CPU at 133 mhz
check lock RTC
value of DIL switch 01
