Ребят, тут такая проблема, у меня уже 3 платы с вот такой вот загрузкой

YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW X !

BATMODE testing
Static Boot from hard disk #0(3)
unable to boot on DISK
Static Boot from No Boot Device selected(0)
Static Boot from flash NAND mother(1)
unable to boot on flash NAND
Static Boot from ethernet(4)

IP address determination
============================

BOOTP request in progress ->0:80:9F:83:BC:A8

*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTo,TOIPRcv,
*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,
*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,
*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,

Connection timed out: BOOTP server not responding.
unable to boot on Ethernet linkк⌡Alize BIOS Monitor
*** BIOS Version 3EH30227GQAA bios100/010.014 ***
*** Generated on  Mar/5/2008 at 14:05 ***
memory test started lng=133169152 with 0
running flash(soldered=1 socket=0)=1,BIOScase:4,BIOSv24:0,verrou=1,algoNOR=1,siz X e=1,base=3FF80000
DIMM characteristics->: JEDEC Manu ID:Й,......
Memory type(EDO,FPM..):0x 4
# of row address:13
# of col address 9
# of module row 1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI:scan_bus for bus 0
PCI:bus=00h,devfn=00h ,[vendor:device]=[1022h/3000h]
PCI:bus=00h,devfn=60h ,[vendor:device]=[100Bh/0020h]
PCI:bus=00h,devfn=98h ,[vendor:device]=[1064h/2101h]
PCI:scan_buses  with 00h secondary buses
PCI:command =     3FFH   for device 00:00
PCI: Assigning I/O space FC00-FCFF for 00:60 BAR=      10
PCI:Assign memory space BFFFF000H to BFFFFFFFH for device 00:60
PCI:command =     3FFH   for device 00:60
PCI:Assign memory space BFFFD000H to BFFFDFFFH for device 00:98
PCI: Assigning I/O space FD00-FD1F for 00:98 BAR=      14
PCI: Unable to handle I/O allocation for 00:98 (FF04) BAR=      18
PCI:command =     3FFH   for device 00:98
assigning irq10 to xchange
B0 = 17
DRCTMCTL = 1E
DRCCTL   =  8
DBCTL    = 11
Set external RTC
Set Internal RTC
No external RTC detected
gpbus sig timing : 0-2-1-2-1-2!

CMOS is available
Xchange PCI mem base OK:        0,mbx= BFFFD000
dsp_accesses.stat_ctrl=    FD00
Xchange PCI IO base OK:        0
Xchange irq OK:  A
PCI command read for natsemi :      347
PCI Master Bit  Setting...
pci_command set to: 357
  0   80   9F   83   BC   A8  ,IRQ 12.on interrupt pin:2
eth0: Transceiver status 0x    7849  advertising      5E1
Flashfx version:700.014.700c
Flash 2Gbit Support activated !!
GC-forced on Soft Error activated !!
NAND Flash Comfiguration:
    CPU  size : 128 MBytes
         free spare blocks: 36
NAND Flash Details:
chip #0 : Type=NAND01GW3B       Id=20F1H Size=128(MBytes)       Unit size=131072        Page Size=2048
time :sec=48,min=12,hour= 3,DoW= 6,date=26,Month= 5,year= 0
time :sec=51,min=12,hour= 3,DoW= 6,date=26,Month= 5,year= 0

ALIZE informations :
       Memory Detected : 131072 Ko
       Flash Detected
       DaughterBoard Detected
               DSP Voip Found : 1
       XCHANGE Detected
               XCHANGE Chip Initialization OK
               Ethernet Found : 1
               Ethernet Chip Initialization OK
       Hard Disk Not Detected
PCM11 selected
CPU at 133 mhz
check lock RTC
value of DIL switch  2

ну а потом все по новой, что можно с этим сделать?перепрошивка поможет?