Доброго времени суток, уважаемые знатоки.
На OXE (R9.1-i1.605-29-ru-c82) перестала загружаться плата GD-3. Случилось это после перепрошивки CS-2.
Log загрузки:
U-Boot 1.3.0-rc3 (Apr 15 2009 - 16:37:27) 3EH30350AAAI bootl100/000.008
Reset Status:
CPU: e300c4, MPC8377, Rev: 21 at 666.666 MHz, CSB: 333 MHz
I2C: ready
DRAM:
DDR DIMM: data bus width is 64 bit without ECC
DDRC ECC mode: OFF
DDR RAM: 256 MB
FLASH: 2 MB
PCI: Bus Dev VenId DevId Class Int
00 17 1064 2102 0000 00
In: serial
Out: serial
Err: serial
Net: TSEC0, TSEC1
eSDHC: 4bit-buswidth mode
SATA: SATA0 [Link: no RDY]
SATA1 [Link: no RDY]
## Booting image at ff836dd8 ...
Image Name: aleboot.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 8436 Bytes = 8.2 kB
Load Address: 00200000
Entry Point: 002017f4
Verifying Checksum ... OK
OK
DIP switch: 0x02
m41t11 Chip
No Prompt
Booting from SDMMC
Hit any key to stop autoboot: 0
## Booting image at ff838f0c ...
Image Name: gpioinit.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 2185 Bytes = 2.1 kB
Load Address: 00200000
Entry Point: 00200620
Verifying Checksum ... OK
OK
Watchdog Started
877 bytes read
## Executing script at 00100000
1851658 bytes read
11565557 bytes read
## Booting image at 00200000 ...
Image Name: Linux-2.6.23.17-020.001
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1851594 Bytes = 1.8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at 00850000 ...
Image Name: OXE_NGP_2.0_int
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 11565493 Bytes = 11 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Booting using the fdt at 0x450000
Loading Ramdisk to 0f497000, end 0ff9e9b5 ... OK
setup_arch: bootmem
ale8377_mg_setup_arch()
arch: exit
Может кто сталкивался с такой проблемой. Подскажите что делать.
На OXE (R9.1-i1.605-29-ru-c82) перестала загружаться плата GD-3. Случилось это после перепрошивки CS-2.
Log загрузки:
U-Boot 1.3.0-rc3 (Apr 15 2009 - 16:37:27) 3EH30350AAAI bootl100/000.008
Reset Status:
CPU: e300c4, MPC8377, Rev: 21 at 666.666 MHz, CSB: 333 MHz
I2C: ready
DRAM:
DDR DIMM: data bus width is 64 bit without ECC
DDRC ECC mode: OFF
DDR RAM: 256 MB
FLASH: 2 MB
PCI: Bus Dev VenId DevId Class Int
00 17 1064 2102 0000 00
In: serial
Out: serial
Err: serial
Net: TSEC0, TSEC1
eSDHC: 4bit-buswidth mode
SATA: SATA0 [Link: no RDY]
SATA1 [Link: no RDY]
## Booting image at ff836dd8 ...
Image Name: aleboot.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 8436 Bytes = 8.2 kB
Load Address: 00200000
Entry Point: 002017f4
Verifying Checksum ... OK
OK
DIP switch: 0x02
m41t11 Chip
No Prompt
Booting from SDMMC
Hit any key to stop autoboot: 0
## Booting image at ff838f0c ...
Image Name: gpioinit.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 2185 Bytes = 2.1 kB
Load Address: 00200000
Entry Point: 00200620
Verifying Checksum ... OK
OK
Watchdog Started
877 bytes read
## Executing script at 00100000
1851658 bytes read
11565557 bytes read
## Booting image at 00200000 ...
Image Name: Linux-2.6.23.17-020.001
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1851594 Bytes = 1.8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at 00850000 ...
Image Name: OXE_NGP_2.0_int
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 11565493 Bytes = 11 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Booting using the fdt at 0x450000
Loading Ramdisk to 0f497000, end 0ff9e9b5 ... OK
setup_arch: bootmem
ale8377_mg_setup_arch()
arch: exit
Может кто сталкивался с такой проблемой. Подскажите что делать.