Добрый день! Плата сервера вызовов на АТС OmniPCX Enterprise не прогружается:
*** BIOS Version 3EH30227GLAA bios100/010.011 ***
*** Generated on Jun/15/2007 at 16:16 ***
memory test started lng=267386880 with 0
running flash(soldered=1 socket=0)=1,BIOScase:4,BIOSv24:0,verrou=1,algoNOR=1,size=1,base=3FF80000
Exc : Nmi
NMI :PIO5(SHUTOK) cleared
DIMM characteristics->: JEDEC Manu ID:.,......
Memory type(EDO,FPM..):0x 4
# of row address:13
# of col address 10
# of module row 1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI:scan_bus for bus 0
PCI:bus=00h,devfn=00h ,[vendor:device]=[1022h/3000h]
PCI:bus=00h,devfn=60h ,[vendor:device]=[100Bh/0020h]
PCI:bus=00h,devfn=98h ,[vendor:device]=[1064h/2101h]
PCI:scan_buses with 00h secondary buses
PCI:command = 3FFH for device 00:00
PCI: Assigning I/O space FC00-FCFF for 00:60 BAR= 10
PCI:Assign memory space BFFFF000H to BFFFFFFFH for device 00:60
PCI:command = 3FFH for device 00:60
PCI:Assign memory space BFFFD000H to BFFFDFFFH for device 00:98
PCI: Assigning I/O space FD00-FD1F for 00:98 BAR= 14
PCI: Unable to handle I/O allocation for 00:98 (FF04) BAR= 18
PCI:command = 3FFH for device 00:98
assigning irq10 to xchange
B0 = 17
DRCTMCTL = 1E
DRCCTL = 8
DBCTL = 11
Set external RTC
Set Internal RTC
No external RTC detected
gpbus sig timing : 0-2-1-2-1-2!
CMOS is available
Xchange PCI mem base OK: 0,mbx= BFFFD000
dsp_accesses.stat_ctrl= FD00
Xchange PCI IO base OK: 0
Xchange irq OK: A
PCI command read for natsemi : 347
PCI Master Bit Setting...
pci_command set to: 357
0 80 9F 74 2E FE ,IRQ 12.on interrupt pin:2
eth0: Transceiver status 0x 7869 advertising 5E1
Hard Disk #0 : Hitachi HTE541660J9AT00 57231 Mo
Parameters :
Type 3
Extended Type 255
Sectors / track 63
Landing Zone 0
Control Byte 0
Write Precomp 0
Heads 16
Nb of Cylinders 16383
HD size(cyl*sec by track*head*sector size) 8455 MO(decimal)
Flashfx version:600.010.500
NAND Flash Comfiguration:
CPU size : 128 MBytes
free spare blocks: 37
NAND Flash Details:
chip #0 : Type= Id=ADF1H Size=128(MBytes) Unit size=131072 Page Size=2048
time :sec= 2,min=32,hour= 0,DoW= 7,date= 1,Month= 1,year= 0
time :sec= 6,min=32,hour= 0,DoW= 7,date= 1,Month= 1,year= 0
ALIZE informations :
Memory Detected : 262144 Ko
Flash Detected
DaughterBoard Not Detected
XCHANGE Detected
XCHANGE Chip Initialization OK
Ethernet Found : 1
Ethernet Chip Initialization OK
Hard Disk Detected
Hard Disk Found : 1
DMA enabled
PCM11 selected
Back Panel NMI disabled
Hard Drive APM supported and enabled -> Current Value is 0x80 ( not optimal )
WARNING !! Possible overload of Load Cycles Count in this Power Mode!!
Try to disable APM.
APM is now disabled.
CPU at 133 mhz
check lock RTC
value of DIL switch 1
YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW !
Static Boot from hard disk #0(3)
valeur index DXCX = FF01FEFF
valeur index DXCX = FF01FEFF
GRUB version 0.5.96 (132096K lower / 261120K upper memory)
[ Minimal BASH-like line editing is supported. For the first word, TAB
lists possible command completions. Anywhere else TAB lists the possible
completions of a device/filename. ]
grub>
Похоже проблема с ПО на жестком диске. Что делать, перезаливать ПО? Или есть другие менее радикальные пути?
*** BIOS Version 3EH30227GLAA bios100/010.011 ***
*** Generated on Jun/15/2007 at 16:16 ***
memory test started lng=267386880 with 0
running flash(soldered=1 socket=0)=1,BIOScase:4,BIOSv24:0,verrou=1,algoNOR=1,size=1,base=3FF80000
Exc : Nmi
NMI :PIO5(SHUTOK) cleared
DIMM characteristics->: JEDEC Manu ID:.,......
Memory type(EDO,FPM..):0x 4
# of row address:13
# of col address 10
# of module row 1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI:scan_bus for bus 0
PCI:bus=00h,devfn=00h ,[vendor:device]=[1022h/3000h]
PCI:bus=00h,devfn=60h ,[vendor:device]=[100Bh/0020h]
PCI:bus=00h,devfn=98h ,[vendor:device]=[1064h/2101h]
PCI:scan_buses with 00h secondary buses
PCI:command = 3FFH for device 00:00
PCI: Assigning I/O space FC00-FCFF for 00:60 BAR= 10
PCI:Assign memory space BFFFF000H to BFFFFFFFH for device 00:60
PCI:command = 3FFH for device 00:60
PCI:Assign memory space BFFFD000H to BFFFDFFFH for device 00:98
PCI: Assigning I/O space FD00-FD1F for 00:98 BAR= 14
PCI: Unable to handle I/O allocation for 00:98 (FF04) BAR= 18
PCI:command = 3FFH for device 00:98
assigning irq10 to xchange
B0 = 17
DRCTMCTL = 1E
DRCCTL = 8
DBCTL = 11
Set external RTC
Set Internal RTC
No external RTC detected
gpbus sig timing : 0-2-1-2-1-2!
CMOS is available
Xchange PCI mem base OK: 0,mbx= BFFFD000
dsp_accesses.stat_ctrl= FD00
Xchange PCI IO base OK: 0
Xchange irq OK: A
PCI command read for natsemi : 347
PCI Master Bit Setting...
pci_command set to: 357
0 80 9F 74 2E FE ,IRQ 12.on interrupt pin:2
eth0: Transceiver status 0x 7869 advertising 5E1
Hard Disk #0 : Hitachi HTE541660J9AT00 57231 Mo
Parameters :
Type 3
Extended Type 255
Sectors / track 63
Landing Zone 0
Control Byte 0
Write Precomp 0
Heads 16
Nb of Cylinders 16383
HD size(cyl*sec by track*head*sector size) 8455 MO(decimal)
Flashfx version:600.010.500
NAND Flash Comfiguration:
CPU size : 128 MBytes
free spare blocks: 37
NAND Flash Details:
chip #0 : Type= Id=ADF1H Size=128(MBytes) Unit size=131072 Page Size=2048
time :sec= 2,min=32,hour= 0,DoW= 7,date= 1,Month= 1,year= 0
time :sec= 6,min=32,hour= 0,DoW= 7,date= 1,Month= 1,year= 0
ALIZE informations :
Memory Detected : 262144 Ko
Flash Detected
DaughterBoard Not Detected
XCHANGE Detected
XCHANGE Chip Initialization OK
Ethernet Found : 1
Ethernet Chip Initialization OK
Hard Disk Detected
Hard Disk Found : 1
DMA enabled
PCM11 selected
Back Panel NMI disabled
Hard Drive APM supported and enabled -> Current Value is 0x80 ( not optimal )
WARNING !! Possible overload of Load Cycles Count in this Power Mode!!
Try to disable APM.
APM is now disabled.
CPU at 133 mhz
check lock RTC
value of DIL switch 1
YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW !
Static Boot from hard disk #0(3)
valeur index DXCX = FF01FEFF
valeur index DXCX = FF01FEFF
GRUB version 0.5.96 (132096K lower / 261120K upper memory)
[ Minimal BASH-like line editing is supported. For the first word, TAB
lists possible command completions. Anywhere else TAB lists the possible
completions of a device/filename. ]
grub>
Похоже проблема с ПО на жестком диске. Что делать, перезаливать ПО? Или есть другие менее радикальные пути?
.