Переустанавливалось ПО R7.1 CPUe-2 для восстановления
работоспособности АТС.
Порт Config. в режиме TTY login т.е
виден лог работы АТС до момента старта Linux.
По сообщениям в окне LoL-ы утановка ПО завершилось
успешно .
После перезагрузки станция не отвечает на ping 192.168.92.246
Кофигурирование через TTY тоже не возможно.
Лог процесса инсталляции ниже
BI.DBG : NS + NS
CMOS is available
eth dynamic address used
PCI command read for natsemi : 347
PCI Master Bit Setting...
pci_command set to: 357
0 80 9F 2E 4 AC , IRQ 12.
eth0: Transceiver status 0x 7869 advertising 5E1
eth dynamic address used
PCI command read for natsemi : 347
PCI Master Bit Setting...
pci_command set to: 357
0 80 9F 2E 4 AC , IRQ 15.
eth1: Transceiver status 0x 7849 advertising 5E1
eth0 : init OK
eth1 : init OK
Hard Disk #0 : Hitachi HTS543280L9A300 76319 Mo
Parameters :
Type 3
Extended Type 255
Sectors / track 63
Landing Zone 0
Control Byte 0
Write Precomp 0
Heads 16
Nb of Cylinders 16383
HD size(cyl*sec by track*head*sector size) 8455 MO(decimal)
Flashfx version:800.002
Found SS mode on Main
NAND Flash Comfiguration:
CPU size : 64 MBytes
free spare blocks: 79
NAND Flash Details:
chip #0 : Type=HY27US08 Id=AD76H Size=64(MBytes) Unit size=16384 Page Size=512
eth dynamic address used
time :sec= 0,min= 0,hour= 0,DoW= 7,date= 1,Month= 1,year= 0
time :sec= 0,min= 0,hour= 0,DoW= 7,date= 1,Month= 1,year= 0
time :sec= 0,min= 0,hour= 0,DoW= 7,date= 1,Month= 1,year= 0
ALIZE informations :
Memory Detected : 262144 Ko
Flash Detected
DaughterBoard Not Detected
XCHANGE Detected
XCHANGE Chip Initialization OK
Ethernet Found : 2
Ethernet Chip Initialization OK
Hard Disk Detected
Hard Disk Found : 1
check lock RTC
value of DIL switch B
USB Base address is FC21
Hard Drive APM supported and disabled
Optimal. No change needed.
YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW !
test the BATMODE
!!! BATMODE !!!
throttling test
Boot from bootp+hard disk #0
eth0: Setting 1 (0 half 1 full) based on negotiated link capability.
eth dynamic address used
IP address determination
==========================
BOOTP request in progress -> 0:80:9F:2E:4:AC
*RcvTO,TOIPRcv*RcvTO,TOIPRcvBootp resp IP addr src:192.168.92.100
bootp server and TFTP server are equal
TFTP server IP addr(siaddr):192.168.92.100
eth source address=0:1E:33:1:8C:40
bootfile=install_flash.tftp
Domain name:yourdomain.com
Our Hostname:downloadl(192.168.92.2)
Netmask:255.255.255.0
My IP address
192.168.92.2
My SUBNET mask
255.255.255.0
TFTPLOAD STARTED using ip=192.168.92.100-Bootp Server Pupkin.com-File Name install_flash.tftp
size of last packet: 103
TFTPLOAD COMPLETE-file size 103
cmd received:vmlinux.bin;1099632;BIN;1048576;1048576
X initrd_inst.gz;6574372;RAMDISK;4194304;0
X boot;0;BOOT;0;1048576
size of file loaded: 67H at 664CH
j= 0 file-fct type= 7 ,file name= vmlinux.bin ,length= 1099632 ,address=1048576 start=1048576
j= 1 file-fct type= 1 ,file name= initrd_inst.gz ,length= 6574372 ,address=4194304 start=0
j= 2 file-fct type= 5 ,file name= boot ,length= 0 ,address=0 start=1048576
j= 3 file-fct type= 0 ,file name= ,length= 0 ,address=0 start=0
j= 4 file-fct type= 0 ,file name= ,length= 0 ,address=0 start=0
j= 5 file-fct type= 0 ,file name= ,length= 0 ,address=0 start=0
j= 6 file-fct type= 0 ,file name= ,length= 0 ,address=0 start=0
j= 7 file-fct type= 0 ,file name= ,length= 0 ,address=0 start=0
j= 8 file-fct type= 0 ,file name= ,length= 0 ,address=0 start=0
j= 9 file-fct type= 0 ,file name= ,length= 0 ,address=0 start=0
config action number=3
TFTPLOAD STARTED using ip=192.168.92.100-Bootp Server pupkin.com -File Name vmlinux.bin
X
X size of last packet: 368
TFTPLOAD COMPLETE-file size 1099632
TFTPLOAD STARTED using ip=192.168.92.100-Bootp Server pupkin.com -File Name initrd_inst.gz
X
X
X
X
X
X
X
X
X
X
..size of last packet: 292
TFTPLOAD COMPLETE-file size 6574372
14995=total packets received
14997=total packets transmitted
8364573=total bytes received
961392=total bytes transmitted
0=bad packets received
0=packet transmit problems
0=no space in linux buffers
0=no space available in linux
0=multicast packets received
0=collisions
0=length_errors
0=receiver ring buff overflow
0=recved pkt with crc error
0=recv'd frame alignment error
0=recv'r fifo overrun
0=receiver missed packet
0=tx_aborted_errors
0=tx_carrier_errors
0=tx_fifo_errors
0=tx_heartbeat_errors
0=tx_window_errors
0=rx_compressed
0=tx_compressed
start kernel: 100000
Shutdown of the interface 0 = 0
new console=ttyS1
!!!!!!!!!!!!!!!!!
LOLA Window
14:43:55 192.168.92.2 Connected.
14:43:56 ..... 2
14:43:56 192.168.92.2 Connecting flash...
14:43:57 Formating Flash...
14:44:20 ..... 24
14:44:21 Formating HD...
14:45:27 ..... 67
14:45:28 192.168.92.2 Transferring software...
14:46:18 ..... 1634
14:46:22 Backuping soft from HD to NAND
14:50:31 ..... 246
14:50:31 192.168.92.2 Flash programming terminated successful.
14:50:32 192.168.92.2 Disconnected.
!!!!!!!!!!!!!!!!!
Reboot OXO
*** CPUe-1 Board version 3EU23006ACBC 02 ***
*** CPUe-1 Layout 3 ***
*** BIOS Version 3EU24001AFAA bspiii100/006.001 ***
*** Generated on Apr/17/2008 at 13:16 ***
*** Pentium III @ 695 ICH ***
THROTTLING: Critical local(BOARD) temperature set to 72 ░C
Critical remote(CPU) temperature set to 92 ░C
BI.DBG : NS + NS
CMOS is available
PCI command read for natsemi : 347
PCI Master Bit Setting...
pci_command set to: 357
0 80 9F 89 D9 9A , IRQ 12.
eth0: Transceiver status 0x 7869 advertising 5E1
PCI command read for natsemi : 347
PCI Master Bit Setting...
pci_command set to: 357
0 80 9F 89 D9 9B , IRQ 15.
eth1: Transceiver status 0x 7849 advertising 5E1
eth0 : init OK
eth1 : init OK
Hard Disk #0 : Hitachi HTS543280L9A300 76319 Mo
Parameters :
Type 3
Extended Type 255
Sectors / track 63
Landing Zone 0
Control Byte 0
Write Precomp 0
Heads 16
Nb of Cylinders 16383
HD size(cyl*sec by track*head*sector size) 8455 MO(decimal)
Flashfx version:800.002
Found SS mode on Main
NAND Flash Comfiguration:
CPU size : 64 MBytes
free spare blocks: 79
NAND Flash Details:
chip #0 : Type=HY27US08 Id=AD76H Size=64(MBytes) Unit size=16384 Page Size=512
time :sec= 0,min= 0,hour= 0,DoW= 7,date= 1,Month= 1,year= 0
time :sec= 0,min= 0,hour= 0,DoW= 7,date= 1,Month= 1,year= 0
time :sec= 0,min= 0,hour= 0,DoW= 7,date= 1,Month= 1,year= 0
ALIZE informations :
Memory Detected : 262144 Ko
Flash Detected
DaughterBoard Not Detected
XCHANGE Detected
XCHANGE Chip Initialization OK
Ethernet Found : 2
Ethernet Chip Initialization OK
Hard Disk Detected
Hard Disk Found : 1
check lock RTC
value of DIL switch F
USB Base address is FC21
Hard Drive APM supported and enabled -> Current Value is 0x80 ( not optimal )
WARNING !! Possible overload of Load Cycles Count in this Power Mode!!
Try to disable APM.
APM is now disabled.
YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW !
test the BATMODE
!!! BATMODE !!!
throttling test
wait for shuddown reset from back panel
NMI AUTHORIZED :PIO5(SHUTOK) set
shut ok de-asserted
Dynamic Boot from bootp+hard disk #0
Watchdog started with 2 min
Watchdog started with 2 min
eth0: Setting 1 (0 half 1 full) based on negotiated link capability.
IP address determination
==========================
BOOTP request in progress -> 0:80:9F:89:D9:9A
*RcvTO,TOIPRcv*RcvTO,TOIPRcv*RcvTO,TOIPRcv*RcvTO,TOIPRcv*RcvTO,TOIPRcv*RcvTO,
TOIPRcv*RcvTO,TOIPRcv*RcvTO,TOIPRcv*RcvTO,TOIPRcv*RcvTO,TOIPRcv
Connection timed out:BOOTP server not responding.
new console=ttyS1
valeur index DXCX = FF01FEFF
GRUB - Detected P3 BIOS Version (3EU24001AFAA bspiii100/006.001)
BOOT_DRIVE = 80, oneshot = FF
valeur index DXCX = FF01FEFF
GRUB version 0.5.92 (1024K lower / 261120K upper memory)
Use keys for selecting an entry
Press enter to boot, 'e' to edit or 'c' for a command-line.
Linux X
Booting 'Linux' ...
[Linux-bzImage, setup=0x800, size=0x7D8A0]
[Linux-initrd @ 0xFAE3000, 0x51C400 bytes]
