Здравствуйте, Уважаемые.
Имеется одна большая станция с выносами. Релиз 9. На выносах платы GD, PCS и абонентские. С одного выноса прислали на ремонт GD и PCS. Когда все было подключено пинга не было на GD и PCS. PCS загружается нормально. В GD не могу зайти поверить настройки. Подскажите, как быть.

ù+Alize BIOS Monitor
*** BIOS Version 3EH30227GQAA bios100/010.014 ***
*** Generated on  Mar/5/2008 at 14:05 ***
memory test started lng=133169152 with 0
running flash(soldered=1 socket=0)=1,BIOScase:4,BIOSv24:0,verrou=1,algoNOR=1,size=1,base=3FF80000
DIMM characteristics->: JEDEC Manu ID:ê,......
Memory type(EDO,FPM..):0x 4
# of row address:13
# of col address 9  
# of module row 1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI:scan_bus for bus 0
PCI:bus=00h,devfn=00h ,[vendor:device]=[1022h/3000h]
PCI:bus=00h,devfn=60h ,[vendor:device]=[100Bh/0020h]
PCI:bus=00h,devfn=98h ,[vendor:device]=[1064h/2101h]
PCI:scan_buses  with 00h secondary buses
PCI:command =     3FFH   for device 00:00
PCI: Assigning I/O space FC00-FCFF for 00:60 BAR=      10
PCI:Assign memory space BFFFF000H to BFFFFFFFH for device 00:60
PCI:command =     3FFH   for device 00:60
PCI:Assign memory space BFFFD000H to BFFFDFFFH for device 00:98
PCI: Assigning I/O space FD00-FD1F for 00:98 BAR=      14
PCI: Unable to handle I/O allocation for 00:98 (FF04) BAR=      18
PCI:command =     3FFH   for device 00:98
assigning irq10 to xchange
B0 = 17
DRCTMCTL = 1E
DRCCTL   =  8
DBCTL    = 11
Set external RTC
Set Internal RTC
No external RTC detected
gpbus sig timing : 0-2-1-2-1-2!

CMOS is available
Xchange PCI mem base OK:        0,mbx= BFFFD000
dsp_accesses.stat_ctrl=    FD00
Xchange PCI IO base OK:        0
Xchange irq OK:  A
PCI command read for natsemi :      347
PCI Master Bit  Setting...
pci_command set to: 357
  0   80   9F   82   E9   36  ,IRQ 12.on interrupt pin:2
eth0: Transceiver status 0x    7869  advertising      5E1
Flashfx version:700.014.700c
Flash 2Gbit Support activated !!
GC-forced on Soft Error activated !!
NAND Flash Comfiguration:
    CPU  size : 128 MBytes
         free spare blocks: 37
NAND Flash Details:
chip #0 : Type=NAND01GW3B Id=20F1H Size=128(MBytes) Unit size=131072 Page Size=2048
time :sec= 8,min= 1,hour=10,DoW= 7,date=15,Month= 1,year= 0
time :sec=12,min= 1,hour=10,DoW= 7,date=15,Month= 1,year= 0

ALIZE informations :
Memory Detected : 131072 Ko
Flash Detected
DaughterBoard Detected
DSP Voip Found : 1
XCHANGE Detected
XCHANGE Chip Initialization OK
Ethernet Found : 1
Ethernet Chip Initialization OK
Hard Disk Not Detected
PCM11 selected
CPU at 133 mhz
check lock RTC
value of DIL switch  2


YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW !

BATMODE testing
Static Boot from hard disk #0(3)
unable to boot on DISK
Static Boot from No Boot Device selected(0)
Static Boot from flash NAND mother(1)
unable to boot on flash NAND
Static Boot from ethernet(4)
eth0: Setting 1 (0 half 1 full) based on negotiated link  capability.

IP address determination
============================

BOOTP request in progress ->0:80:9F:82:E9:36

*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOI
PRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvT
O,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,
Connection timed out: BOOTP server not responding.
unable to boot on Ethernet linkû+Alize BIOS Monitor
*** BIOS Version 3EH30227GQAA bios100/010.014 ***
*** Generated on  Mar/5/2008 at 14:05 ***
memory test started lng=133169152 with 0
running flash(soldered=1 socket=0)=1,BIOScase:4,BIOSv24:0,verrou=1,algoNOR=1,size=1,base=3FF80000
DIMM characteristics->: JEDEC Manu ID:ê,......
Memory type(EDO,FPM..):0x 4
# of row address:13
# of col address 9  
# of module row 1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI:scan_bus for bus 0



И далее по кругу тоже самое.