Уважаемы форумчане помогите пожалуйста, досталась АТС Alcatel OmniPCX Medium (Soft REL R310/28.3), не могу зайти в неё. FAN не горит. Дэфолтный адрес насколько мне объяснили не менялся, но он не пингуется. Спаял COM кабель по следующей схеме:

RJ-45   com
1         8
2         6
3         2
4         5
5         5
6         3
7         4
8         7
подключился через порт config и у меня следующая бесконечно повторяющаяся картина (не знаю что дальше делать):

CMOS is available
PCI command read for natsemi : 00000347
PCI Master Bit  Setting...
pci_command set to:0357
0000 0080 009f 0034 00fd 0030  , IRQ 12.
eth0: Transceiver status 0x00007849  advertising 000005e1
PCI command read for natsemi : 00000347
PCI Master Bit  Setting...
pci_command set to:0357
0000 0080 009f 0034 00fd 0031  , IRQ 15.
eth1: Transceiver status 0x00007849  advertising 000005e1
eth0 : init OK
eth1 : init OK
Hard Disk #0 : TOSHIBA MK2023GAS                       19076 Mo
Parameters :
       Type            00000
       Extended Type   00255
       Sectors / track 00063
       Landing Zone    00000
       Control Byte    00000
       Write Precomp   00000
       Heads           00016
       Nb of Cylinders 16383
       HD size(cyl*sec by track*head*sector size)   08455 MO(decimal)
interrupt flash UNMASKED
Flashfx revision number 520.003.000
NAND flash Mount init interrupt
NAND flash Mount init interrupt
NAND flash drive No. 0 successfully mounted
NAND Flash Comfiguration:
    CPU  size : 32 MBytes
         free spare blocks: 38
    XMEM size : 0 MBytes
NAND Flash Details:
    chip #0 : Type=TC58256 Id=9875H Size=32(MBytes) Unit size=16384 Page Size=512
time :sec=11,min=02,hour=08,DoW=01,date=02,Month=01,year=00
time :sec=16,min=02,hour=08,DoW=01,date=02,Month=01,year=00

ALIZE informations :
       Memory Detected : 262144 Ko
       Flash Detected
       DaughterBoard Not Detected
       XCHANGE Detected
               XCHANGE Chip Initialization OK
               Ethernet Found : 2
               Ethernet Chip Initialization OK
       Hard Disk Detected
               Hard Disk Found : 1
check lock RTC
value of DIL switch 0f
USB Base address is fc21
HD trace unlocked

No change
HD trace locked



YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW !

test the BATMODE
ATMODE !!!
ait for shuddown reset from back panel
NMI AUTHORIZED  :PIO5(SHUTOK) set
shut ok
Boot from bootp+hard disk #0
Watchdog started with 2 min
Watchdog started with 2 min

IP address determination
==========================

BOOTP request in progress -> 0:80:9f:34:fd:30

*RcvTO,TOIPRcv*RcvTO,TOIPRcv*RcvTO,TOIPRcv*RcvTO,TOIPRcv*RcvTO,TOIPRcv*RcvTO,TOIPRcv*RcvTO,TOIPRcv*RcvTO,TOIPRcv*RcvTO,TOIPRcv*RcvTO,TOI
Connection timed out:BOOTP server not responding.
new console=ttyS1
valeur  index DXCX = ff01feff
GRUB - Detected P3 BIOS Version (3EU24001AAGL bspiii100/004.013)

BOOT_DRIVE = 80, ones hot = FF

valeur  index DXCX = ff01feff
GRUB version 0.5.92  (1024K lower / 261120K upper memory)
TAB lists the possible completions and ESC for exit

GRUB stopping after 1039 reading, last virt sector=00000000H, phys sector=00000000H, return code=00000010H

*** CPUe-1 Board version  3EU23006ACAC 02  ***
*** CPUe-1 Layout 3 ***
*** BIOS Version 3EU24001AAGL bspiii100/004.013 ***
*** Generated on  Mar/17/2004 at 16:05 ***

*** Pentium III @ 697 ***

THROTTLING: Critical local(BOARD) temperature set to 72 ’C
           Critical remote(CPU)  temperature set to 92 ’C

BI.DBG : NS + NS.