Подскажите в чём беда может быть?
Проблема вообщем такая!!
Я перезолил ПО на GD-ку, перезапустил её и всё было нормально!! но когда ещё раз выключил-включил она не загружается и выдает:
*** BIOS Version 3EH30227GQAA bios100/010.014 ***
*** Generated on  Mar/5/2008 at 14:05 ***
memory test started lng=133169152 with 0
running flash(soldered=1 socket=0)=1,BIOScase:4,BIOSv24:0,verrou=1,algoNOR=1,size=1,base=3FF80000
DIMM characteristics->: JEDEC Manu ID:к,......
Memory type(EDO,FPM..):0x 4
# of row address:13
# of col address 9  
# of module row 1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI:scan_bus for bus 0
PCI:bus=00h,devfn=00h ,[vendor:device]=[1022h/3000h]
PCI:bus=00h,devfn=60h ,[vendor:device]=[100Bh/0020h]
PCI:bus=00h,devfn=98h ,[vendor:device]=[1064h/2101h]
PCI:scan_buses  with 00h secondary buses
PCI:command =     3FFH   for device 00:00
PCI: Assigning I/O space FC00-FCFF for 00:60 BAR=      10
PCI:Assign memory space BFFFF000H to BFFFFFFFH for device 00:60
PCI:command =     3FFH   for device 00:60
PCI:Assign memory space BFFFD000H to BFFFDFFFH for device 00:98
PCI: Assigning I/O space FD00-FD1F for 00:98 BAR=      14
PCI: Unable to handle I/O allocation for 00:98 (FF04) BAR=      18
PCI:command =     3FFH   for device 00:98
assigning irq10 to xchange
B0 = 17
DRCTMCTL = 1E
DRCCTL   =  8
DBCTL    = 11
Set external RTC
Set Internal RTC
No external RTC detected
gpbus sig timing : 0-2-1-2-1-2!

CMOS is available
Xchange PCI mem base OK:        0,mbx= BFFFD000
dsp_accesses.stat_ctrl=    FD00
Xchange PCI IO base OK:        0
Xchange irq OK:  A
PCI command read for natsemi :      347
PCI Master Bit  Setting...
pci_command set to: 357
  0   80   9F   73   B9   25  ,IRQ 12.on interrupt pin:2
eth0: Transceiver status 0x    7869  advertising      5E1
Flashfx version:700.014.700c
Flash 2Gbit Support activated !!
GC-forced on Soft Error activated !!
NAND Flash Comfiguration:
    CPU  size : 128 MBytes
         free spare blocks: 4
NAND Flash Details:
chip #0 : Type=HY27UF08         Id=ADF1H Size=128(MBytes)       Unit size=131072        Page Size=2048
time :sec=46,min=29,hour=23,DoW= 7,date=15,Month= 1,year= 0
time :sec=49,min=29,hour=23,DoW= 7,date=15,Month= 1,year= 0

ALIZE informations :
       Memory Detected : 131072 Ko
       Flash Detected
       DaughterBoard Detected
               DSP Voip Found : 1
       XCHANGE Detected
               XCHANGE Chip Initialization OK
               Ethernet Found : 1
               Ethernet Chip Initialization OK
       Hard Disk Not Detected
PCM11 selected
CPU at 133 mhz
check lock RTC
value of DIL switch  2


YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW !

BATMODE testing
Static Boot from hard disk #0(3)
unable to boot on DISK
Static Boot from No Boot Device selected(0)
Static Boot from flash NAND mother(1)
unable to boot on NAND flash drive 0
unable to boot on flash NAND
Static Boot from ethernet(4)
eth0: Setting 1 (0 half 1 full) based on negotiated link  capability.

IP address determination
============================

BOOTP request in progress ->0:80:9F:73:B9:25

*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,
*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,
*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,
*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,

Подскажите вчём беда может быть?

Народ подскажите, пожалуйста, не образованному;)))
У меня CS навернулся винт, я поставил новый. Как мне теперь залить туда всё что нужно?
Заранее благодарен!!!!!