доброго времени суток, вышла из строя nand 128мб alcatel nand01gw3b2bn6, выручите дампом
Лог загрузки прикладываю
Alize BIOS Monitor
*** BIOS Version 3EH30227GKAA bios100/010.009 ***
*** Generated on Jul/24/2006 at 16:40 ***
memory test started lng=133169152 with 0
running flash(soldered=1 socket=0)=1,BIOScase:4,BIOSv24:0,verrou=1,algoNOR=1,siz
e=1,base=3FF80000
DIMM characteristics->: JEDEC Manu ID:к,яяяяяя
Memory type(EDO,FPM..):0x 4
# of row address:13
# of col address 9
# of module row 1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI:scan_bus for bus 0
PCI:bus=00h,devfn=00h ,[vendor:device]=[1022h/3000h]
PCI:bus=00h,devfn=60h ,[vendor:device]=[100Bh/0020h]
PCI:bus=00h,devfn=98h ,[vendor:device]=[1064h/2101h]
PCI:scan_buses with 00h secondary buses
PCI:command = 3FFH for device 00:00
PCI: Assigning I/O space FC00-FCFF for 00:60 BAR= 10
PCI:Assign memory space BFFFF000H to BFFFFFFFH for device 00:60
PCI:command = 3FFH for device 00:60
PCI:Assign memory space BFFFD000H to BFFFDFFFH for device 00:98
PCI: Assigning I/O space FD00-FD1F for 00:98 BAR= 14
PCI: Unable to handle I/O allocation for 00:98 (FF04) BAR= 18
PCI:command = 3FFH for device 00:98
assigning irq10 to xchange
B0 = 17
DRCTMCTL = 1E
DRCCTL = 8
DBCTL = 11
Set external RTC
Set Internal RTC
No external RTC detected
gpbus sig timing : 0-2-1-2-1-2!
CMOS is available
Xchange PCI mem base OK: 0,mbx= BFFFD000
dsp_accesses.stat_ctrl= FD00
Xchange PCI IO base OK: 0
Xchange irq OK: A
PCI command read for natsemi : 347
PCI Master Bit Setting...
pci_command set to: 357
0 80 9F 60 46 B2 ,IRQ 12.on interrupt pin:2
eth0: Transceiver status 0x 7849 advertising 5E1
Flashfx version:600.010.500
Watchdog disabled
NAND flash: Search of bad blocks on device 0, please wait...
Number of bad blocks found: 40 --> TOO MUCH !!! NOT ACCEPTABLE
NAND Flash Comfiguration:
CPU size : 128 MBytes
free spare blocks: 0
YOU MUST REPLACE CPU NAND FLASH HARDWARE
or try to use the flashnand function : clear NAND bad blocks list
NAND Flash Details:
chip #0 : Type=NAND01GW3B Id=20F1H Size=128(MBytes) Unit size=131072
Page Size=2048
time :sec=28,min=45,hour=17,DoW= 1,date= 9,Month= 1,year= 0
time :sec=31,min=45,hour=17,DoW= 1,date= 9,Month= 1,year= 0
ALIZE informations :
Memory Detected : 131072 Ko
Flash Detected
DaughterBoard Detected
DSP Voip Found : 1
XCHANGE Detected
XCHANGE Chip Initialization OK
Ethernet Found : 1
Ethernet Chip Initialization OK
Hard Disk Not Detected
PCM11 selected
CPU at 133 mhz
check lock RTC
value of DIL switch 2
YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW
!
BATMODE testing
Static Boot from hard disk #0(3)
unable to boot on DISK
Static Boot from No Boot Device selected(0)
Static Boot from flash NAND mother(1)
unable to boot on flash NAND
Static Boot from ethernet(4)
IP address determination
============================
BOOTP request in progress ->0:80:9F:60:46:B2
*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,
Лог загрузки прикладываю
Alize BIOS Monitor
*** BIOS Version 3EH30227GKAA bios100/010.009 ***
*** Generated on Jul/24/2006 at 16:40 ***
memory test started lng=133169152 with 0
running flash(soldered=1 socket=0)=1,BIOScase:4,BIOSv24:0,verrou=1,algoNOR=1,siz
e=1,base=3FF80000
DIMM characteristics->: JEDEC Manu ID:к,яяяяяя
Memory type(EDO,FPM..):0x 4
# of row address:13
# of col address 9
# of module row 1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI:scan_bus for bus 0
PCI:bus=00h,devfn=00h ,[vendor:device]=[1022h/3000h]
PCI:bus=00h,devfn=60h ,[vendor:device]=[100Bh/0020h]
PCI:bus=00h,devfn=98h ,[vendor:device]=[1064h/2101h]
PCI:scan_buses with 00h secondary buses
PCI:command = 3FFH for device 00:00
PCI: Assigning I/O space FC00-FCFF for 00:60 BAR= 10
PCI:Assign memory space BFFFF000H to BFFFFFFFH for device 00:60
PCI:command = 3FFH for device 00:60
PCI:Assign memory space BFFFD000H to BFFFDFFFH for device 00:98
PCI: Assigning I/O space FD00-FD1F for 00:98 BAR= 14
PCI: Unable to handle I/O allocation for 00:98 (FF04) BAR= 18
PCI:command = 3FFH for device 00:98
assigning irq10 to xchange
B0 = 17
DRCTMCTL = 1E
DRCCTL = 8
DBCTL = 11
Set external RTC
Set Internal RTC
No external RTC detected
gpbus sig timing : 0-2-1-2-1-2!
CMOS is available
Xchange PCI mem base OK: 0,mbx= BFFFD000
dsp_accesses.stat_ctrl= FD00
Xchange PCI IO base OK: 0
Xchange irq OK: A
PCI command read for natsemi : 347
PCI Master Bit Setting...
pci_command set to: 357
0 80 9F 60 46 B2 ,IRQ 12.on interrupt pin:2
eth0: Transceiver status 0x 7849 advertising 5E1
Flashfx version:600.010.500
Watchdog disabled
NAND flash: Search of bad blocks on device 0, please wait...
Number of bad blocks found: 40 --> TOO MUCH !!! NOT ACCEPTABLE
NAND Flash Comfiguration:
CPU size : 128 MBytes
free spare blocks: 0
YOU MUST REPLACE CPU NAND FLASH HARDWARE
or try to use the flashnand function : clear NAND bad blocks list
NAND Flash Details:
chip #0 : Type=NAND01GW3B Id=20F1H Size=128(MBytes) Unit size=131072
Page Size=2048
time :sec=28,min=45,hour=17,DoW= 1,date= 9,Month= 1,year= 0
time :sec=31,min=45,hour=17,DoW= 1,date= 9,Month= 1,year= 0
ALIZE informations :
Memory Detected : 131072 Ko
Flash Detected
DaughterBoard Detected
DSP Voip Found : 1
XCHANGE Detected
XCHANGE Chip Initialization OK
Ethernet Found : 1
Ethernet Chip Initialization OK
Hard Disk Not Detected
PCM11 selected
CPU at 133 mhz
check lock RTC
value of DIL switch 2
YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW
!
BATMODE testing
Static Boot from hard disk #0(3)
unable to boot on DISK
Static Boot from No Boot Device selected(0)
Static Boot from flash NAND mother(1)
unable to boot on flash NAND
Static Boot from ethernet(4)
IP address determination
============================
BOOTP request in progress ->0:80:9F:60:46:B2
*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,*RcvTO,TOIPRcv,
Изменено: underoath - 03.05.2018 14:06:59