В продолжение темы
На PCS установлена GD3, перестала видеть SD-карточку. Сделали следующее. Отформатировали SD в ext4, GD3 её увидела. Далее, для загрузки софта,PCS был переведен в режим MAIN, запущен DHCP на CS2 со статикой по mac-адресу GD3 и записью "Configuration file + MG3:-/downbin/mg3/binmg3start", прописан lanpbx с tftp и адресом cpu платы cs2. GD3 загружается с CS2, форматирует SD, копирует софт на нее. После перезагрузки прописаны сетевые параметры в местной сети, где в качестве CPU role address указывается адрес станции к которой привязан PCS. В итоге GD3 прогружается и медиагейтвей становится в сервис. А затем происходит самопроизвольная перезагрузка CS2 и GD3 (pcscopy не запускался), при этом GD3 перестает видеть SD-карту, пишет Bad partition 1 и далее No SD card detected!
Когда gd3 пытается грузиться со станции к которой привязан pcs, то происходит вот что:
[Start cpl_sli2.ko]
end of load appli modules phase
[Start normal_startup rescue_off]
'binmg3
Downloading /DHS3bin/downbin/mg3/binmg3 from 10.15.8.4
BINMG AUTHENTICATION OK
Authentication successed
create_install_a called
create_install_b called
Function create_bootloader_conf to be implemented
Function create_oneshot_conf to be implemented
Checking other files
Checking binmg3country version
e28624c5a3e73fb9bd98cc8ab1dd2cde2e9d85eb
/etc/rc.d/init.d/newimage2: sha1sum on binmg3country done. cmp is going to run:
e28624c5a3e73fb9bd98cc8ab1dd2cde2e9d85eb
------------------------------------------------------------
Checking for new DSP deliveries...
Procesing binamcvb642x.df
Downloading /DHS3bin/downbin/mg3/binamcvb642x.df from 10.15.8.4
binamcvb642x AUTHENTICATION OK
Delivery file binamcvb642x.df downloaded
No upgrade needed for binamcvb642x
Procesing bin642xconf.df
Downloading /DHS3bin/downbin/mg3/bin642xconf.df from 10.15.8.4
bin642xconf AUTHENTICATION OK
Delivery file bin642xconf.df downloaded
No upgrade needed for bin642xconf
------------------------------------------------------------
switch_init_cmd : pINTIPA=0
Startup inetd
Standard version
[Start build_hosts 0]
Startup completed - awaiting user login ...
STARTFILE ASKED := startmg3
DTLS mode for CS := DISABLED
switch_init_cmd : pINTIPA=0
[Startup script ended : 90init]
(Mngt_Sig::connect_process) Valid Connect Messsage...!
FGP in xeno_mg d22cb7ec and size of msg 96
FGP:
mg3 login:
Rack 0 is a large
Inserting country module : xeno_country_param_RU.ko
[Start build_hosts 2]
FSNE mode DISABLED, no datas to save in flash, establishment confirmed
insmod for module xeno_country_p
====== record_country : 19 (RUSSIA)
aram_RU.ko
Ъ
U-Boot 1.3.0-rc3 (Jan 12 2012 - 14:42:54) 3EH30350AAAS bootl100/000.018
Reset Status:
CPU: e300c4, MPC8377, Rev: 21 at 666.666 MHz, CSB: 333 MHz
I2C: ready
DRAM:
DDR DIMM: data bus width is 64 bit without ECC
DDRC ECC mode: OFF
DDR RAM: 256 MB
FLASH: 2 MB
PCI: Bus Dev VenId DevId Class Int
00 17 1064 2102 0000 00
In: serial
Out: serial
Err: serial
Net: TSEC0, TSEC1
eSDHC: OCR busy timeout
SATA: SATA0 [Link: no RDY]
SATA1 [Link: no RDY]
## Booting image at ff836df0 ...
Image Name: aleboot.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 9576 Bytes = 9.4 kB
Load Address: 00200000
Entry Point: 00201bd4
Verifying Checksum ... OK
OK
DIP switch: 0x02
m41t11 Chip
No Prompt
Press ^B^I to enter into the Bios menu 0 Booting from SDMMC
Hit any key to stop autoboot: 0
## Booting image at ff839398 ...
Image Name: gpioinit.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 2185 Bytes = 2.1 kB
Load Address: 00200000
Entry Point: 00200620
Verifying Checksum ... OK
OK
Watchdog Started
** Bad partition 1 **
Resetting the board.Щ
U-Boot 1.3.0-rc3 (Jan 12 2012 - 14:42:54) 3EH30350AAAS bootl100/000.018
Reset Status: Software Hard, External/Internal Soft, External/Internal Hard
CPU: e300c4, MPC8377, Rev: 21 at 666.666 MHz, CSB: 333 MHz
I2C: ready
DRAM:
DDR DIMM: data bus width is 64 bit without ECC
DDRC ECC mode: OFF
DDR RAM: 256 MB
FLASH: 2 MB
PCI: Bus Dev VenId DevId Class Int
00 17 1064 2102 0000 00
In: serial
Out: serial
Err: serial
Net: TSEC0, TSEC1
eSDHC: OCR busy timeout
SATA: SATA0 [Link: no RDY]
SATA1 [Link: no RDY]
## Booting image at ff836df0 ...
Image Name: aleboot.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 9576 Bytes = 9.4 kB
Load Address: 00200000
Entry Point: 00201bd4
Verifying Checksum ... OK
OK
DIP switch: 0x02
m41t11 Chip
No Prompt
Press ^B^I to enter into the Bios menu 0 Booting from SDMMC
Hit any key to stop autoboot: 0
## Booting image at ff839398 ...
Image Name: gpioinit.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 2185 Bytes = 2.1 kB
Load Address: 00200000
Entry Point: 00200620
Verifying Checksum ... OK
OK
Watchdog Started
** Bad partition 1 **
Resetting the board.Ъ
На PCS установлена GD3, перестала видеть SD-карточку. Сделали следующее. Отформатировали SD в ext4, GD3 её увидела. Далее, для загрузки софта,PCS был переведен в режим MAIN, запущен DHCP на CS2 со статикой по mac-адресу GD3 и записью "Configuration file + MG3:-/downbin/mg3/binmg3start", прописан lanpbx с tftp и адресом cpu платы cs2. GD3 загружается с CS2, форматирует SD, копирует софт на нее. После перезагрузки прописаны сетевые параметры в местной сети, где в качестве CPU role address указывается адрес станции к которой привязан PCS. В итоге GD3 прогружается и медиагейтвей становится в сервис. А затем происходит самопроизвольная перезагрузка CS2 и GD3 (pcscopy не запускался), при этом GD3 перестает видеть SD-карту, пишет Bad partition 1 и далее No SD card detected!
Когда gd3 пытается грузиться со станции к которой привязан pcs, то происходит вот что:
[Start cpl_sli2.ko]
end of load appli modules phase
[Start normal_startup rescue_off]
'binmg3
Downloading /DHS3bin/downbin/mg3/binmg3 from 10.15.8.4
BINMG AUTHENTICATION OK
Authentication successed
create_install_a called
create_install_b called
Function create_bootloader_conf to be implemented
Function create_oneshot_conf to be implemented
Checking other files
Checking binmg3country version
e28624c5a3e73fb9bd98cc8ab1dd2cde2e9d85eb
/etc/rc.d/init.d/newimage2: sha1sum on binmg3country done. cmp is going to run:
e28624c5a3e73fb9bd98cc8ab1dd2cde2e9d85eb
------------------------------------------------------------
Checking for new DSP deliveries...
Procesing binamcvb642x.df
Downloading /DHS3bin/downbin/mg3/binamcvb642x.df from 10.15.8.4
binamcvb642x AUTHENTICATION OK
Delivery file binamcvb642x.df downloaded
No upgrade needed for binamcvb642x
Procesing bin642xconf.df
Downloading /DHS3bin/downbin/mg3/bin642xconf.df from 10.15.8.4
bin642xconf AUTHENTICATION OK
Delivery file bin642xconf.df downloaded
No upgrade needed for bin642xconf
------------------------------------------------------------
switch_init_cmd : pINTIPA=0
Startup inetd
Standard version
[Start build_hosts 0]
Startup completed - awaiting user login ...
STARTFILE ASKED := startmg3
DTLS mode for CS := DISABLED
switch_init_cmd : pINTIPA=0
[Startup script ended : 90init]
(Mngt_Sig::connect_process) Valid Connect Messsage...!
FGP in xeno_mg d22cb7ec and size of msg 96
FGP:
mg3 login:
Rack 0 is a large
Inserting country module : xeno_country_param_RU.ko
[Start build_hosts 2]
FSNE mode DISABLED, no datas to save in flash, establishment confirmed
insmod for module xeno_country_p
====== record_country : 19 (RUSSIA)
aram_RU.ko
Ъ
U-Boot 1.3.0-rc3 (Jan 12 2012 - 14:42:54) 3EH30350AAAS bootl100/000.018
Reset Status:
CPU: e300c4, MPC8377, Rev: 21 at 666.666 MHz, CSB: 333 MHz
I2C: ready
DRAM:
DDR DIMM: data bus width is 64 bit without ECC
DDRC ECC mode: OFF
DDR RAM: 256 MB
FLASH: 2 MB
PCI: Bus Dev VenId DevId Class Int
00 17 1064 2102 0000 00
In: serial
Out: serial
Err: serial
Net: TSEC0, TSEC1
eSDHC: OCR busy timeout
SATA: SATA0 [Link: no RDY]
SATA1 [Link: no RDY]
## Booting image at ff836df0 ...
Image Name: aleboot.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 9576 Bytes = 9.4 kB
Load Address: 00200000
Entry Point: 00201bd4
Verifying Checksum ... OK
OK
DIP switch: 0x02
m41t11 Chip
No Prompt
Press ^B^I to enter into the Bios menu 0 Booting from SDMMC
Hit any key to stop autoboot: 0
## Booting image at ff839398 ...
Image Name: gpioinit.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 2185 Bytes = 2.1 kB
Load Address: 00200000
Entry Point: 00200620
Verifying Checksum ... OK
OK
Watchdog Started
** Bad partition 1 **
Resetting the board.Щ
U-Boot 1.3.0-rc3 (Jan 12 2012 - 14:42:54) 3EH30350AAAS bootl100/000.018
Reset Status: Software Hard, External/Internal Soft, External/Internal Hard
CPU: e300c4, MPC8377, Rev: 21 at 666.666 MHz, CSB: 333 MHz
I2C: ready
DRAM:
DDR DIMM: data bus width is 64 bit without ECC
DDRC ECC mode: OFF
DDR RAM: 256 MB
FLASH: 2 MB
PCI: Bus Dev VenId DevId Class Int
00 17 1064 2102 0000 00
In: serial
Out: serial
Err: serial
Net: TSEC0, TSEC1
eSDHC: OCR busy timeout
SATA: SATA0 [Link: no RDY]
SATA1 [Link: no RDY]
## Booting image at ff836df0 ...
Image Name: aleboot.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 9576 Bytes = 9.4 kB
Load Address: 00200000
Entry Point: 00201bd4
Verifying Checksum ... OK
OK
DIP switch: 0x02
m41t11 Chip
No Prompt
Press ^B^I to enter into the Bios menu 0 Booting from SDMMC
Hit any key to stop autoboot: 0
## Booting image at ff839398 ...
Image Name: gpioinit.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 2185 Bytes = 2.1 kB
Load Address: 00200000
Entry Point: 00200620
Verifying Checksum ... OK
OK
Watchdog Started
** Bad partition 1 **
Resetting the board.Ъ
