Добрый день.
Столкнулся с ситуацией, что не могу пролить INTIP3 из коробки.
PCI пробовал разные, до последней 5.5 версии, софт в плату льет, далее Verifying Checksum ... Bad Data CRC, reset и снова по кругу.
Кто сталкивался с подобным, куда копать?
Столкнулся с ситуацией, что не могу пролить INTIP3 из коробки.
PCI пробовал разные, до последней 5.5 версии, софт в плату льет, далее Verifying Checksum ... Bad Data CRC, reset и снова по кругу.
Кто сталкивался с подобным, куда копать?
Код |
---|
Resetting the board.э U-Boot 1.3.0-rc3 (Jan 12 2012 - 14:42:54) 3EH30350AAAS bootl100/000.018 Reset Status: Software Hard, External/Internal Soft, External/Internal Hard CPU: e300c4, MPC8377, Rev: 21 at 666.666 MHz, CSB: 333 MHz I2C: ready DRAM: DDR DIMM: data bus width is 64 bit without ECC DDRC ECC mode: OFF DDR RAM: 256 MB FPGA: /soc@e0000000/gpio@c00/fpga@01f00000: FPGA4C1NV reloading... done FLASH: 2 MB PCI: Bus Dev VenId DevId Class Int 00 17 1064 2102 0000 00 00 18 1064 2102 0000 00 00 1d 10ee 0300 0b40 ff In: serial Out: serial Err: serial Net: TSEC0, TSEC1 eSDHC: 4bit-buswidth mode SATA: SATA0 [Link: no RDY] SATA1 [Link: no RDY] ## Booting image at ff836df0 ... Image Name: aleboot.bin Image Type: PowerPC U-Boot Standalone Program (uncompressed) Data Size: 9576 Bytes = 9.4 kB Load Address: 00200000 Entry Point: 00201bd4 Verifying Checksum ... OK OK m41t11 Chip No Prompt Press ^B^I to enter into the Bios menu 0 Reloading default boot sequence. Booting from SDMMC Hit any key to stop autoboot: 0 ## Booting image at ff839398 ... Image Name: gpioinit.bin Image Type: PowerPC U-Boot Standalone Program (uncompressed) Data Size: 2185 Bytes = 2.1 kB Load Address: 00200000 Entry Point: 00200620 Verifying Checksum ... OK OK Watchdog Started ** Unable to read "/boot/u-boot.scr" from mmc 0:1 ** Resetting the board.э U-Boot 1.3.0-rc3 (Jan 12 2012 - 14:42:54) 3EH30350AAAS bootl100/000.018 Reset Status: Software Hard, External/Internal Soft, External/Internal Hard CPU: e300c4, MPC8377, Rev: 21 at 666.666 MHz, CSB: 333 MHz I2C: ready DRAM: DDR DIMM: data bus width is 64 bit without ECC DDRC ECC mode: OFF DDR RAM: 256 MB FPGA: /soc@e0000000/gpio@c00/fpga@01f00000: FPGA4C1NV reloading... done FLASH: 2 MB PCI: Bus Dev VenId DevId Class Int 00 17 1064 2102 0000 00 00 18 1064 2102 0000 00 00 1d 10ee 0300 0b40 ff In: serial Out: serial Err: serial Net: TSEC0, TSEC1 eSDHC: 4bit-buswidth mode SATA: SATA0 [Link: no RDY] SATA1 [Link: no RDY] ## Booting image at ff836df0 ... Image Name: aleboot.bin Image Type: PowerPC U-Boot Standalone Program (uncompressed) Data Size: 9576 Bytes = 9.4 kB Load Address: 00200000 Entry Point: 00201bd4 Verifying Checksum ... OK OK m41t11 Chip No Prompt Press ^B^I to enter into the Bios menu 6 1- Load from Hard disk 2- Load from SDcard 3- Load from Ethernet 4- Load from Hard disk & bootp 5- Load from SDcard & bootp 6- Display MAC addresses , CPUID and Serial Number 7- Reset Your choice followed by carriage return : Time out Booting from NETWORK BOOTP Hit any key to stop autoboot: 0 ## Booting image at ff839398 ... Image Name: gpioinit.bin Image Type: PowerPC U-Boot Standalone Program (uncompressed) Data Size: 2185 Bytes = 2.1 kB Load Address: 00200000 Entry Point: 00200620 Verifying Checksum ... OK OK Watchdog Started Speed: 1000, full duplex Using TSEC0 device BOOTP broadcast request 1 in progress ---> 00:80:9f:fd:51:af Using TSEC0 device TFTP from server 10.10.10.15; our IP address is 10.10.10.16 Filename '/DHS3bin/downbin/intip3/binintip3start'. Load address: 0x100000 Loading: # done Bytes transferred = 689 (2b1 hex) ## Executing script at 00100000 Speed: 1000, full duplex Using TSEC0 device TFTP from server 10.10.10.15; our IP address is 10.10.10.16 Filename '/DHS3bin/downbin/intip3/binintip3linux'. Load address: 0x4000000 Loading: ################################################################# ################################################################# ########### done Bytes transferred = 2006429 (1e9d9d hex) Speed: 1000, full duplex Using TSEC0 device TFTP from server 10.10.10.15; our IP address is 10.10.10.16 Filename '/DHS3bin/downbin/intip3/binintip3rdimg'. Load address: 0x6000000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### done Bytes transferred = 13772396 (d2266c hex) ## Booting image at 04000000 ... Image Name: Linux-2.6.23.17-020.001 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 2006365 Bytes = 1.9 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... Bad Data CRC Resetting the board.э |